hey,
did you update usbutilits and udev rpms also.For the problem you are
facing i will definitely look for some solution.
Regards
Ankush
On Thu, 17 Feb 2005 00:23:09 +0100, Donald Raikes (draikes)
<no-reply-gw(a)fcp.homelinux.org> wrote:
Hello, Ankush
Even before I sent my last message to this list, I was completely up to date.
I am running the latest stable kernel update: kernel-2.6.10-1.760_FC3
I am also running the latest stable update of hotplug: hotplug-2004_04_01-8.1
As I mentioned, I was running both of these when I sent my last message.
Also, my problem is that my devices dissappear, not that they are not
detected. If I unplug a device that has "dissappeared" and plug it into a
different USB2 port, it is immediately detected. Also, if I unplug a device
and plug it back into the same port (I've only tried that after waiting a few
minutes), the device magically reappears. I can't remember though if the
device is actually functional. Also, I am now running a PCI USB2 card, and
I've been using the burner successfully ever since. I just tried to use our
scanner while it was plugged into that PCI USB2 card, and I ended up having
to reboot about five times. When I plugged it back into one of the front
USB2 ports on our machine (this port is connected directly to the mainboard
instead of being a PCI card) the strangest thing happened: I could finally
scan without the scanner hanging. I hate to do it, but I think I will take
the scanner to a machine that I have access to that runs Windows XP. I will
see how it behaves...
If there is a development or testing kernel or hotplug RPM that you think I
should try, please let me know.
Again, our devices get detected and re-detected just fine, the problem is that
they just dissappear....
Steven P. Ulrick
Just to throw my 2 cents into this discussion.
I installed FC3 kernel 2.6.10-1.741 onto my gateway 7200x system.
When i plugged in my usb braille display, it sometimes detects and other times it
doesn't.
I ran yum to get fully up to date, and still have the problem.
I just unplugged and re-plugged the display into one of the usb ports on the back of the
pc, the /var/logs/messages file shows the following info:
Feb 16 09:08:02 oasis brltty[623]: USB URB status error 84: Invalid or incomplete
multibyte or wide character.
Feb 16 09:08:02 oasis brltty[623]: USB configuration set error 71: Protocol error.
Feb 16 09:08:02 oasis kernel: usb 2-1: USB disconnect, address 38
Feb 16 09:08:02 oasis kernel: usb 2-1.1: USB disconnect, address 39
Feb 16 09:08:07 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 40
Feb 16 09:08:07 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:07 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:08 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 41
Feb 16 09:08:10 oasis kernel: usb 2-1: USB disconnect, address 40
Feb 16 09:08:10 oasis kernel: usb 2-1.1: USB disconnect, address 41
Feb 16 09:08:10 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 42
Feb 16 09:08:10 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:10 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:11 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 43
Feb 16 09:08:11 oasis kernel: usb 2-1.1: config index 0 descriptor too short (expected
32, got 8)
Feb 16 09:08:11 oasis kernel: usb 2-1.1: config 1 has 0 interfaces, different from the
descriptor's value: 1
Feb 16 09:08:12 oasis brltty[623]: USB interface claim error 2: No such file or
directory.
Feb 16 09:08:17 oasis brltty[623]: USB interface claim error 2: No such file or
directory.
Feb 16 09:08:18 oasis kernel: usb 2-1: USB disconnect, address 42
Feb 16 09:08:18 oasis kernel: usb 2-1.1: USB disconnect, address 43
Feb 16 09:08:20 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 44
Feb 16 09:08:20 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:20 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:21 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 45
Feb 16 09:08:23 oasis brltty[623]: Alva driver, version 2.2
my /proc/bus/usb/device file contains the following info:
T: Bus=02 Lev=02 Prnt=44 Port=00 Cnt=01 Dev#= 45 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=06b0 ProdID=0001 Rev=20.02
S: Manufacturer=ALVA B.V.
S: Product=ALVA 544 Satellite
S: SerialNumber=54400015
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbfs
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=20ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 8 Ivl=0ms
As a side note, I have greater success if iI disable haldaemon.
--
This is an email sent via the webforum on
http://fcp.homelinux.org
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe:
http://www.redhat.com/mailman/listinfo/fedora-list