On Thu, 2007-02-01 at 19:16 +0000, Beartooth wrote:
On Thu, 01 Feb 2007 09:17:11 -0800, Rick Stevens wrote:
> On Thu, 2007-02-01 at 16:58 +0000, Beartooth wrote:
[...]
>> >
>> > So verify that the "e100" driver is loaded via
"/sbin/lsmod".
>>
>> All right, making assurance doubly sure, I logged in using "su -
root"
>> *and* did cd before /sbin/lsmod.
>>
>> I see columns labelled Module, Size, and Used by. "e100" is not
mentioned
>> in any of them -- and without a Net connection, I have no way to download
>> anything. Can I get it off the CDs, as I must have been doing before?
>
> It should have been installed by default. Verify that you have the
> following file on the system:
>
> /lib/modules/`uname -r`/kernel/drivers/net/e100.ko
>
> (yes, those are graves or "backticks"--the other character on the
"~"
> key).
I think I must have retyped that correctly, because bash turned the uname
part into "2.6.19-1.2895.fc6" and left the rest. But I also think I do not
have it, because bash then added ":No such file or directory"
Hmmm. Let me try:
[root@prophead ~]# ls /lib/modules/`uname -r`/kernel/drivers/net/e100.ko
/lib/modules/2.6.18-1.2869.fc6/kernel/drivers/net/e100.ko
> If you do have the file, then (as root via the "su -") try this
> command:
>
> modprobe e100
>
> to force the driver to load.
I tried that anyway, and sure enough (I think) it responded with a line
saying "-bash: modeprobe: command not found"
You must be root ("su -") and it's "modprobe" (only one
"e"). If you're
not root, then "/sbin/modprobe e100".
I did the install, as usual, in custom mode -- and tried to leave
out
games, chat, and anything else I thought surely I'd never use (but took
lots of development stuff, because I do run betas like Pan and Dillo).
This has been my usual practice for years -- only, this time, I must have
mis-guessed something inessential that I should have taken.
Or this may be the same machine on which recently I got so snarled up in
yum dependency hell that I finally commanded "yum remove elfutils" -- and
didn't read the list of other things it would remove carefully enough. (I
don't think it is. I think I just gave up, wiped that install with DBAN,
and installed again.)
Anybody know a straightforward way to get it from the CDs?
It's part of the kernel RPM. If you've installed the kernel, you've got
it.
So, here's what to do:
1. Run "su -" and become root
2. Run "ls /lib/modules/`uname -r`/kernel/drivers/net/e100.ko" and
verify you have the file.
3. Delete the "/etc/sysconfig/hwconf" file and run kudzu to rediscover
your hardware:
rm /etc/sysconfig/hwconf
kudzu
4. Run "modprobe e100" to load the driver
5. Run "ifconfig" and verify you have device eth0.
6. Try to configure eth0 using the command line:
ifconfig eth0 192.168.0.254 netmask 255.255.255.0
7. Try "ifconfig" again. You should see something like:
[root@prophead ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0F:FE:02:16:38
inet addr:192.168.0.254 Bcast:192.168.0.255
Mask:255.255.255.0
inet6 addr: fe80::20f:feff:fe02:1638/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:33007499 errors:0 dropped:0 overruns:0 frame:0
TX packets:15837216 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2322911622 (2.1 GiB) TX bytes:616269113 (587.7 MiB)
Interrupt:193
The "HWaddr", "inet6 addr:", "Interrupt" and traffic info
(RX/TX bytes)
will differ from what I show above, but you get the idea.
8. If you see that stuff, great! Edit the /etc/modprobe.conf file and
add a line that reads:
alias eth0 e100
9. Run your normal configuration. Delete all existing configs and put
in the new stuff you want.
That should handle it.
----------------------------------------------------------------------
- Rick Stevens, Senior Systems Engineer rstevens(a)vitalstream.com -
- VitalStream, Inc.
http://www.vitalstream.com -
- -
- The gene pool could use a little chlorine. -
----------------------------------------------------------------------