Hi Pete,
Sorry things have been kinda busy at work so I haven't had much time to test. In short it still doesn't work. Details are listed below. Thanks again for following up!
Running kernel: 2.6.10-1.741_FC3
modprobe.conf: alias usb-controller ehci-hcd alias usb-controller1 uhci-hcd
Insert the SanDisk Cruzer 1GB drive and get the following in /var/log/messages: Feb 1 10:16:23 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 10 Feb 1 10:16:23 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:23 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:24 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 12 Feb 1 10:16:24 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:24 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:25 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 ... Feb 1 10:16:27 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:27 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:28 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 19 ... Feb 1 10:16:30 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:30 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71
If you need I can test other USB2.0 devices later this week.
Cheers, Harry
Pete Zaitcev wrote:
On Sun, 09 Jan 2005 22:53:33 -0500, Harry Hoffman hhoffman@ip-solutions.net wrote:
It's 2.6.9-1.724_FC3
I'm guessing it's a problem with ehci as well as none of my USB2.0 devices seem to work with ehci loaded :-(
Hello, Harry:
What is the situation now with 2.6.10 stream (2.6.10-1.741_FC3)?
-- Pete
Hi, You might want to try to load usbcore with old_scheme_first=y or use_both_schemes=y option. See if it helps. Good luck Petr
Harry Hoffman wrote:
Hi Pete,
Sorry things have been kinda busy at work so I haven't had much time to test. In short it still doesn't work. Details are listed below. Thanks again for following up!
Running kernel: 2.6.10-1.741_FC3
modprobe.conf: alias usb-controller ehci-hcd alias usb-controller1 uhci-hcd
Insert the SanDisk Cruzer 1GB drive and get the following in /var/log/messages: Feb 1 10:16:23 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 10 Feb 1 10:16:23 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:23 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:24 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 12 Feb 1 10:16:24 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:24 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:25 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 ... Feb 1 10:16:27 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:27 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:28 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 19 ... Feb 1 10:16:30 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:30 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71
If you need I can test other USB2.0 devices later this week.
Cheers, Harry
Pete Zaitcev wrote:
On Sun, 09 Jan 2005 22:53:33 -0500, Harry Hoffman hhoffman@ip-solutions.net wrote:
It's 2.6.9-1.724_FC3
I'm guessing it's a problem with ehci as well as none of my USB2.0 devices seem to work with ehci loaded :-(
Hello, Harry:
What is the situation now with 2.6.10 stream (2.6.10-1.741_FC3)?
-- Pete
I haven't been following this thread completely - (do USB-2 devices work with older kernels?)
You might want to try WinXP (connect the USB-2 device) and see if you get an error of type:
"connecting usb-2 device to usb-1 port" This indicates hardware problem.
Satish
On Wed, 2 Feb 2005, [windows-1252] Petr ?imon wrote:
Hi, You might want to try to load usbcore with old_scheme_first=y or use_both_schemes=y option. See if it helps. Good luck Petr
Harry Hoffman wrote:
Hi Pete,
Sorry things have been kinda busy at work so I haven't had much time to test. In short it still doesn't work. Details are listed below. Thanks again for following up!
Running kernel: 2.6.10-1.741_FC3
modprobe.conf: alias usb-controller ehci-hcd alias usb-controller1 uhci-hcd
Insert the SanDisk Cruzer 1GB drive and get the following in /var/log/messages: Feb 1 10:16:23 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 10 Feb 1 10:16:23 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:23 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:24 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 12 Feb 1 10:16:24 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:24 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:25 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 ... Feb 1 10:16:27 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:27 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:28 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 19 ... Feb 1 10:16:30 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:30 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71
If you need I can test other USB2.0 devices later this week.
Cheers, Harry
Pete Zaitcev wrote:
On Sun, 09 Jan 2005 22:53:33 -0500, Harry Hoffman hhoffman@ip-solutions.net wrote:
It's 2.6.9-1.724_FC3
I'm guessing it's a problem with ehci as well as none of my USB2.0 devices seem to work with ehci loaded :-(
Hello, Harry:
What is the situation now with 2.6.10 stream (2.6.10-1.741_FC3)?
-- Pete
El mié, 02-02-2005 a las 07:57 -0600, Satish Balay escribió:
I haven't been following this thread completely - (do USB-2 devices work with older kernels?)
You might want to try WinXP (connect the USB-2 device) and see if you get an error of type:
"connecting usb-2 device to usb-1 port" This indicates hardware problem.
Satish
On Wed, 2 Feb 2005, [windows-1252] Petr ?imon wrote:
Hi, You might want to try to load usbcore with old_scheme_first=y or use_both_schemes=y option. See if it helps. Good luck Petr
Harry Hoffman wrote:
Hi Pete,
Sorry things have been kinda busy at work so I haven't had much time to test. In short it still doesn't work. Details are listed below. Thanks again for following up!
Running kernel: 2.6.10-1.741_FC3
modprobe.conf: alias usb-controller ehci-hcd alias usb-controller1 uhci-hcd
Insert the SanDisk Cruzer 1GB drive and get the following in /var/log/messages: Feb 1 10:16:23 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 10 Feb 1 10:16:23 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:23 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:24 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 12 Feb 1 10:16:24 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:24 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:25 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 ... Feb 1 10:16:27 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:27 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:28 n1-22-129 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 19 ... Feb 1 10:16:30 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110Feb 1 10:16:30 n1-22-129 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71 Feb 1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, error -71
If you need I can test other USB2.0 devices later this week.
Cheers, Harry
Pete Zaitcev wrote:
On Sun, 09 Jan 2005 22:53:33 -0500, Harry Hoffman hhoffman@ip-solutions.net wrote:
It's 2.6.9-1.724_FC3
I'm guessing it's a problem with ehci as well as none of my USB2.0 devices seem to work with ehci loaded :-(
Hello, Harry:
What is the situation now with 2.6.10 stream (2.6.10-1.741_FC3)?
-- Pete
I haven't been following this thread either, but it happens by chance that I own exactly the same model of usb stick: SanDisk Cruzer mini 1.0 GB (USB 2 supported). Curiously I've just tried and works as expected...sticked it in "hot- plug" manner, and automatically an icon appears on the desktop (first into "computer" access icon), without needing manual mounting from the CLI. My system is a FC3 updated to its last kernel into a PC box -including USB 2.0 support. Please, have a look at the below infos, maybe they could be useful to you; if not enough, feel free to ask to me to post whatever content else. That's the limit of my knowledge about this.
[daniel@primates-plm ~]$ uname -r 2.6.10-1.741_FC3 [daniel@primates-plm ~]$
[daniel@primates-plm ~]$ dmesg | grep usb usb 1-2: new high speed USB device using ehci_hcd and address 5 usbcore: registered new driver usb-storage usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete usb 1-2: USB disconnect, address 5 usb 1-2: new high speed USB device using ehci_hcd and address 6 usb-storage: device found at 6 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete [daniel@primates-plm ~]$
[daniel@primates-plm ~]$ mount | grep usbdisk /dev/sdc1 on /media/usbdisk type vfat (rw,nosuid,nodev,sync,noatime,iocharset=utf8,user=daniel) [daniel@primates-plm ~]$
[daniel@primates-plm ~]$ cat /etc/fstab | grep usbdisk /dev/sdc1 /media/usbdisk vfat pamconsole,exec,noauto,iocharset=utf8,noatime,sync,managed 0 0 [daniel@primates-plm ~]$
-this latest entry for fstab is automatically created by the system, nothing to do with a manually root intervention.
That's all. I can manually drag-and-drop files through Nautilus.
BTW, SELinux never enabled (don't know if this do care or not..)
P.S. It comes with a "install.exe" file inside, I don't know what is supposed I have to do with it...:-)
Cheers
Hi,
Damnit! Now I don't know what's going on... Tonight I plug in the usb disk and *blammo* it's recognized, then not, then recognized, then not... then not :-(
Messages are:
Feb 2 23:02:32 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 3 Feb 2 23:02:33 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/all, error -71 Feb 2 23:02:33 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 4 Feb 2 23:02:34 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 4 Feb 2 23:02:34 n1-192-168-4-31 kernel: SCSI subsystem initialized Feb 2 23:02:34 n1-192-168-4-31 kernel: Initializing USB Mass Storage driver... Feb 2 23:02:35 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 5 Feb 2 23:02:36 n1-192-168-4-31 kernel: scsi0 : SCSI emulation for USB Mass Storage devices Feb 2 23:02:36 n1-192-168-4-31 kernel: usbcore: registered new driver usb-storage Feb 2 23:02:36 n1-192-168-4-31 kernel: USB Mass Storage support registered. Feb 2 23:02:40 n1-192-168-4-31 kernel: Vendor: SanDisk Model: Cruzer Mini Rev: 0.2 Feb 2 23:02:40 n1-192-168-4-31 kernel: Type: Direct-Access ANSI SCSI revision: 02 Feb 2 23:02:40 n1-192-168-4-31 scsi.agent[7519]: disk at /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/host0/target0:0:0/0:0:0:0 Feb 2 23:02:40 n1-192-168-4-31 kernel: SCSI device sda: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:02:40 n1-192-168-4-31 kernel: sda: Write Protect is off Feb 2 23:02:40 n1-192-168-4-31 kernel: sda: assuming drive cache: write through Feb 2 23:02:40 n1-192-168-4-31 kernel: SCSI device sda: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:02:40 n1-192-168-4-31 kernel: sda: Write Protect is off Feb 2 23:02:40 n1-192-168-4-31 kernel: sda: assuming drive cache: write through Feb 2 23:02:40 n1-192-168-4-31 kernel: sda: sda1 Feb 2 23:02:40 n1-192-168-4-31 kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 Feb 2 23:02:40 n1-192-168-4-31 fstab-sync[7600]: added mount point /media/usbdisk for /dev/sda1 Feb 2 23:02:41 n1-192-168-4-31 kernel: FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! Feb 2 23:02:41 n1-192-168-4-31 kernel: SELinux: initialized (dev sda1, type vfat), uses genfs_contexts Feb 2 23:02:58 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 5 Feb 2 23:02:58 n1-192-168-4-31 fstab-sync[7743]: removed mount point /media/usbdisk for /dev/sda1 Feb 2 23:02:58 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 6 Feb 2 23:02:58 n1-192-168-4-31 kernel: scsi1 : SCSI emulation for USB Mass Storage devices Feb 2 23:03:03 n1-192-168-4-31 kernel: Vendor: SanDisk Model: Cruzer Mini Rev: 0.2 Feb 2 23:03:03 n1-192-168-4-31 kernel: Type: Direct-Access ANSI SCSI revision: 02 Feb 2 23:03:03 n1-192-168-4-31 kernel: SCSI device sda: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:03:03 n1-192-168-4-31 kernel: sda: Write Protect is off Feb 2 23:03:03 n1-192-168-4-31 kernel: sda: assuming drive cache: write through Feb 2 23:03:03 n1-192-168-4-31 kernel: SCSI device sda: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:03:03 n1-192-168-4-31 kernel: sda: Write Protect is off Feb 2 23:03:03 n1-192-168-4-31 kernel: sda: assuming drive cache: write through Feb 2 23:03:03 n1-192-168-4-31 kernel: sda: sda1 Feb 2 23:03:03 n1-192-168-4-31 kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Feb 2 23:03:03 n1-192-168-4-31 scsi.agent[7853]: disk at /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/host1/target1:0:0/1:0:0:0 Feb 2 23:03:04 n1-192-168-4-31 fstab-sync[7904]: added mount point /media/usbdisk for /dev/sda1 Feb 2 23:03:04 n1-192-168-4-31 kernel: FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! Feb 2 23:03:04 n1-192-168-4-31 kernel: SELinux: initialized (dev sda1, type vfat), uses genfs_contexts Feb 2 23:03:26 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 6 Feb 2 23:03:26 n1-192-168-4-31 fstab-sync[7989]: removed mount point /media/usbdisk for /dev/sda1 Feb 2 23:03:26 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 7 Feb 2 23:03:26 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/all, error -71 Feb 2 23:03:26 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 8 Feb 2 23:03:26 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:03:26 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:03:27 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 11 Feb 2 23:03:27 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:03:27 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:03:28 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 12 Feb 2 23:03:28 n1-192-168-4-31 kernel: scsi2 : SCSI emulation for USB Mass Storage devices Feb 2 23:03:29 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 12 Feb 2 23:03:31 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 13 Feb 2 23:03:31 n1-192-168-4-31 kernel: scsi3 : SCSI emulation for USB Mass Storage devices Feb 2 23:03:36 n1-192-168-4-31 kernel: Vendor: SanDisk Model: Cruzer Mini Rev: 0.2 Feb 2 23:03:36 n1-192-168-4-31 kernel: Type: Direct-Access ANSI SCSI revision: 02 Feb 2 23:03:36 n1-192-168-4-31 kernel: SCSI device sda: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:03:36 n1-192-168-4-31 kernel: sda: Write Protect is off Feb 2 23:03:36 n1-192-168-4-31 kernel: sda: assuming drive cache: write through Feb 2 23:03:36 n1-192-168-4-31 kernel: SCSI device sda: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:03:36 n1-192-168-4-31 kernel: sda: Write Protect is off Feb 2 23:03:36 n1-192-168-4-31 kernel: sda: assuming drive cache: write through Feb 2 23:03:36 n1-192-168-4-31 kernel: sda: sda1 Feb 2 23:03:36 n1-192-168-4-31 kernel: Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0 Feb 2 23:03:36 n1-192-168-4-31 scsi.agent[8217]: disk at /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/host3/target3:0:0/3:0:0:0 Feb 2 23:03:36 n1-192-168-4-31 fstab-sync[8268]: added mount point /media/usbdisk for /dev/sda1 Feb 2 23:03:36 n1-192-168-4-31 kernel: FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! Feb 2 23:03:36 n1-192-168-4-31 kernel: SELinux: initialized (dev sda1, type vfat), uses genfs_contexts Feb 2 23:03:37 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 13 Feb 2 23:03:37 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 14 Feb 2 23:03:37 n1-192-168-4-31 kernel: scsi4 : SCSI emulation for USB Mass Storage devices Feb 2 23:03:38 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 14 Feb 2 23:03:39 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 15 Feb 2 23:03:39 n1-192-168-4-31 kernel: scsi5 : SCSI emulation for USB Mass Storage devices Feb 2 23:03:43 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 15 Feb 2 23:03:43 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 16 Feb 2 23:03:43 n1-192-168-4-31 kernel: scsi6 : SCSI emulation for USB Mass Storage devices Feb 2 23:03:48 n1-192-168-4-31 kernel: Vendor: SanDisk Model: Cruzer Mini Rev: 0.2 Feb 2 23:03:48 n1-192-168-4-31 kernel: Type: Direct-Access ANSI SCSI revision: 02 Feb 2 23:03:48 n1-192-168-4-31 kernel: SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:03:48 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:03:48 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:03:48 n1-192-168-4-31 kernel: SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:03:48 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:03:48 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:03:48 n1-192-168-4-31 kernel: sdb: sdb1 Feb 2 23:03:48 n1-192-168-4-31 kernel: Attached scsi removable disk sdb at scsi6, channel 0, id 0, lun 0 Feb 2 23:03:48 n1-192-168-4-31 kernel: Attached scsi removable disk sdb at scsi6, channel 0, id 0, lun 0 Feb 2 23:03:48 n1-192-168-4-31 scsi.agent[8707]: disk at /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/host6/target6:0:0/6:0:0:0 Feb 2 23:03:48 n1-192-168-4-31 fstab-sync[8757]: added mount point /media/usbdisk1 for /dev/sdb1 Feb 2 23:03:48 n1-192-168-4-31 kernel: FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! Feb 2 23:03:48 n1-192-168-4-31 kernel: SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts Feb 2 23:04:08 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 16 Feb 2 23:04:08 n1-192-168-4-31 fstab-sync[8845]: removed mount point /media/usbdisk1 for /dev/sdb1 Feb 2 23:04:08 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 17 Feb 2 23:04:09 n1-192-168-4-31 kernel: scsi7 : SCSI emulation for USB Mass Storage devices Feb 2 23:04:09 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 17 Feb 2 23:04:11 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 18 Feb 2 23:04:11 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:04:11 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:04:12 n1-192-168-4-31 kernel: usb 1-4: device not accepting address 18, error -71 Feb 2 23:04:12 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 22 Feb 2 23:04:12 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/all, error -71 Feb 2 23:04:13 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 26 Feb 2 23:04:14 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 27 Feb 2 23:04:14 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:04:14 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:04:14 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/all, error -71 Feb 2 23:04:14 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 28 Feb 2 23:04:14 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:04:14 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:04:15 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/64, error -71 Feb 2 23:04:15 n1-192-168-4-31 kernel: scsi8 : SCSI emulation for USB Mass Storage devices Feb 2 23:04:16 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 28 Feb 2 23:04:17 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 29 Feb 2 23:04:17 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:04:17 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:04:18 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/all, error -71 Feb 2 23:04:18 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 31 Feb 2 23:04:18 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:04:18 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:04:18 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/64, error -71 Feb 2 23:04:19 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 32 Feb 2 23:04:19 n1-192-168-4-31 kernel: scsi9 : SCSI emulation for USB Mass Storage devices Feb 2 23:04:24 n1-192-168-4-31 kernel: Vendor: SanDisk Model: Cruzer Mini Rev: 0.2 Feb 2 23:04:24 n1-192-168-4-31 kernel: Type: Direct-Access ANSI SCSI revision: 02 Feb 2 23:04:24 n1-192-168-4-31 kernel: SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:04:24 n1-192-168-4-31 kernel: SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:04:24 n1-192-168-4-31 kernel: SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB) Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:04:24 n1-192-168-4-31 kernel: sdb: sdb1 Feb 2 23:04:24 n1-192-168-4-31 kernel: Attached scsi removable disk sdb at scsi9, channel 0, id 0, lun 0 Feb 2 23:04:24 n1-192-168-4-31 scsi.agent[9183]: disk at /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/host9/target9:0:0/9:0:0:0 Feb 2 23:04:25 n1-192-168-4-31 fstab-sync[9234]: added mount point /media/usbdisk1 for /dev/sdb1 Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb : READ CAPACITY failed. Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb : status=0, message=00, host=7, driver=00 Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb : sense not available. Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:04:25 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 32 Feb 2 23:04:25 n1-192-168-4-31 kernel: scsi9 (0:0): rejecting I/O to dead device Feb 2 23:04:25 n1-192-168-4-31 last message repeated 3 times Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb : READ CAPACITY failed. Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb : status=0, message=00, host=0, driver=04 Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb : sense not available. Feb 2 23:04:25 n1-192-168-4-31 kernel: scsi9 (0:0): rejecting I/O to dead device Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb: Write Protect is off Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb: assuming drive cache: write through Feb 2 23:04:25 n1-192-168-4-31 kernel: sdb:<3>scsi9 (0:0): rejecting I/O to dead device Feb 2 23:04:25 n1-192-168-4-31 kernel: Buffer I/O error on device sdb, logical block 0 Feb 2 23:04:25 n1-192-168-4-31 kernel: scsi9 (0:0): rejecting I/O to dead device Feb 2 23:04:25 n1-192-168-4-31 kernel: Buffer I/O error on device sdb, logical block 0 Feb 2 23:04:25 n1-192-168-4-31 kernel: scsi9 (0:0): rejecting I/O to dead device Feb 2 23:04:25 n1-192-168-4-31 kernel: Buffer I/O error on device sdb, logical block 0 Feb 2 23:04:25 n1-192-168-4-31 kernel: unable to read partition table Feb 2 23:04:25 n1-192-168-4-31 fstab-sync[9316]: removed mount point /media/usbdisk1 for /dev/sdb1 Feb 2 23:04:25 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 33 Feb 2 23:04:25 n1-192-168-4-31 kernel: scsi10 : SCSI emulation for USB Mass Storage devices Feb 2 23:04:27 n1-192-168-4-31 kernel: usb 1-4: USB disconnect, address 33 Feb 2 23:04:28 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 34 Feb 2 23:04:28 n1-192-168-4-31 kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Feb 2 23:04:28 n1-192-168-4-31 kernel: hub 1-0:1.0: hub_port_status failed (err = -32) Feb 2 23:04:28 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/64, error -71 Feb 2 23:04:28 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 35 Feb 2 23:04:29 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 36 Feb 2 23:04:29 n1-192-168-4-31 kernel: usb 1-4: device descriptor read/all, error -71 Feb 2 23:04:29 n1-192-168-4-31 kernel: usb 1-4: new high speed USB device using ehci_hcd and address 37 Feb 2 23:04:29 n1-192-168-4-31 kernel: usb 1-4: device not accepting address 37, error -71