F8 rescued fails on FC7?
by Michael D. Berger
On my dual boot laptop with WinXP and F7, if I try
to start from the F7 rescued, it appears to run
properly. However, with an eye toward installing F8,
if I boot from the F8 rescued, it hangs after printing
the line:
running /sbin/loader
The downloaded rescued iso passed sha1sum, and I tried
it with two different burned disks.
!!Now while typing this, perhaps five minutes later, it
suddenly started correctly!
So what took so long?
Thanks,
Mike.
16 years, 4 months
onboard NIC: Attansic L2
by Dan Thurman
Folks,
Motherboard: P5GC-MX/1333, onboard Attansic L2 NIC chip
Earlier I reported a nightmarish experience trying to get my onboard Attansic
L2 NIC working after compiling the source code for it, installing it, and so
on and could not figure out why the NIC was not turning on the phyiscal link.
I think I understand the symptoms but not the underlying cause.
I reported in my earlier post, that I blamed the twisted pair cable but it
turns out this was not the problem. The cabled is fine. I had to go to my
garbage can to retrieve the cable I almost threw out.
I can repeatedly prove (at least to myself), that under a multiboot situation,
if you boot using w2000/XP, M$ turns ON/OFF/ON the link when coming up and
when it is shutdown/rebooted, it disables the link. It somehow turns the NIC
OFF on reboot/shutdown.
When you bootup Fedora, Fedora goes along as it normally does, probes eth0,
but FAILS to turn ON the link. You CANNOT get Fedora to bring up the link no
matter what you do. The ONLY way to get the link back is to physically power
off the power supply because the motherboard always get's it's power unless
the PS itself is turned off and until the power drains out.
Only then, you can bring up Fedora's OS and get the NIC link to work.
I wonder if M$ plugs microcode into the Attansic L2 chip that renders Fedora
unable to turn on the link OR the code is missing from the Fedora networking
process to turn ON the link.
Can someone in development look into this and let me know what is going on?
At the moment, I have a temporary solution for now but I'd like to make sure
no other helpless chap faces this problem like I did for weeks trying to
figure this out.
Regards,
Dan
16 years, 4 months
Anyone seen radeon driver fail to find DVI?
by Tom Horsley
Haven't had a chance to gather much data on this, but on a machine at home
with a fairly old radeon card (might be a 9200 or 9600, I can't look right
now), debian etch has no problem running the display with the xorg radeon
driver it has, but fedora 8 can't talk to the display.
When I look at the log file, I see it believes that it should be talking
to DDC_VGA (which isn't connected), doesn't find a monitor (which makes
sense), and refuses to talk.
The log when I boot debian doesn't mention VGA at all, but goes right
to the DVI connector and works fine.
Just wondered if this rings any bells for anyone before I kill a
lot of time to examine it in more detail.
16 years, 4 months
Possible bug with TypeError in Python
by Aaron Konstam
The following seems like an bug in python in both f7 and f8 but I would
like input before I post a bugzilla. It seems the exception handler
cannot trap the TypeError in python.
For example:
def plus(a,b):
try:
return(a+b)
except TypeError:
return None
If we define plus as above and call it with: plus(3,) we should get
nothing returned. Instead we get:
Traceback (most recent call last):
File "./calculator", line 47, in <module>
exec("register=op[tokens[0]](register)")
File "<string>", line 1, in <module>
TypeError: plus() takes exactly 2 arguments (1 given)
This seems like a bug. An ideas out there?
--
=======================================================================
Please keep your hands off the secretary's reproducing equipment.
=======================================================================
Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam(a)sbcglobal.net
16 years, 4 months
Customizing Fedora Core 6
by potat0
Dear All,
I am working on customizing fedora core 6 with limited packages,and some additional packages. I trimmed all packages to 1.4 GB and planning to make installation disks(probably 2 CDs).
Now I have the same directory structure what CD1 has, but only difference is RPMS directory contains all trimmed pacakages.
I have resolved all the package dependencies using "rpm --test". My query is how can I divide the RPMs so that we can accomodate in 2 CDs.
Please provide me some suggestions or procedure for doing this
Praveen
New Delhi
--
This is an email sent via The Fedora Community Portal https://fcp.surfsite.org
https://fcp.surfsite.org/modules/newbb/viewtopic.php?post_id=236607&topic...
If you think, this is spam, please report this to webmaster(a)fcp.surfsite.org and/or blame praveecbt(a)yahoo.co.in.
16 years, 4 months
USB disk won't mount during boot
by Larry Breyer
I have three different Dell desktops. They are running
FC5, FC6, and F7, respectively. I mention this because
the problem does not occur on FC6. I have Western Digital
USB drives with ext3 filesystems attached to each.
On the FC5 and F7 machines the boot process fails to mount
the USB drive. There is some complaint about an invalid ext3
filesystem. But, after the machines are fully booted, I can
mount the USB drives without any problem.
Is the mount being attempted before the drivers are in place?
Is there a way to resolve this problem?
Thank you!
--
Larry Breyer
Systems Administrator, Computer Services
Salk Institute for Biological Studies
858-453-4100 x1981 Fax:858-554-0572
16 years, 4 months
gettext function not found by Perl module
by M. Fioretti
Greetings,
I need to install the gettext-1.05 perl module from CPAN because
some inherited , very obscure unmaintenable scripts I _need_ to run on FC8
64 bit need it.
When I run the perl Makefile.PL command, I get:
[root@polaris gettext-1.05]# perl Makefile.PL
checking for gettext... no
checking for gettext in -lintl... no
gettext function not found. Please install libintl at Makefile.PL line 18
but I don't know anymore where to find this libintl thing. After the first
time I got this error, I did:
yum install gettext
yum install perl-libintl
yum install perl-gettext
yum install libintl
yum install gettext-devel
and nothing changed, I still get that error. yum search libintl only returns:
perl-libintl.x86_64 : Internationalization library for Perl, compatible
with gettext
what else? I've even installed by hand the libintl-perl and
Locale::Maketext::Gettext modules from CPAN, and nothing changes, I still
get that error. What do I need to install to make it go away?
Thank you in advance for any feedback,
Marco
PS: if it helps, the error message comes from this piece of Makefile.PL:
unless (conftest("char *x = gettext(\"foo\");", "gettext", 0)) {
# try with -lintl
$libs = "-lintl";
unless (conftest("char *x = gettext(\"foo\");", "gettext", 0)) {
unlink("conftest.c");
unlink("conftest");
die "gettext function not found. Please install libintl";
}
--
Help *everybody* love Free Standards and Software:
http://digifreedom.net
16 years, 4 months
libGL error: open DRM failed (Operation not permitted) Fedora-8-xfce
by Frank Murphy
PCI-Card loaded first in bios.
libGL error: open DRM failed (Operation not permitted)
so:
dmesg | grep agp
Linux agpgart interface v0.102
agpgart: Detected an Intel i810 Chipset.
agpgart: detected 4MB dedicated video ram.
agpgart: AGP aperture is 64M @ 0xe80000
This is my inbuild video-chip.
Below is my PCI-Card.
dmesg | grep drm
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.28.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
How do I prevent the error(s).
Frank
16 years, 4 months
CD and DVD ISO images
by John Summerfield
The latest Fedora newsletter triggered this. Someone was asking about
CD-sized ISO images.
For some time I've wondered whether it might be a Good Thing for distros
to create a bunch of CD-sized ISO images, and then for the DVD-sized ISO
image simply glue the lot into a single ISO image that boots the
installer and installs as usual. I don't see much point to making
different-sized install media that are so different.
Anaconda already has to logic to loop-mount ISO images, it just needs to
be applied to the "CDROM" install path.
There would be space advantages to all who host the distro; they'd
simply host the DVD images.
Users who want the CD images would download the DVD image, loop mount it
on Linux or OS X (I think there's brand-X software for Windows too) and
then extract the ISO images to burn or not.
I'm assuming nobody (Debian users excepted) downloads less than a full
set of images.
Most, but not all, of my too-numerous computers have DVD drives, and
right now I'm looking at installing something that I downloaded as a DVD
image on a system that hasn't a DVD drive.
What do others think?
--
Cheers
John
-- spambait
1aaaaaaa(a)coco.merseine.nu Z1aaaaaaa(a)coco.merseine.nu
-- Advice
http://webfoot.com/advice/email.top.php
http://www.catb.org/~esr/faqs/smart-questions.html
http://support.microsoft.com/kb/555375
You cannot reply off-list:-)
16 years, 4 months