Hello, I have a toshiba laptop with a miniPCI EL-2511MP PLUS 802.11/b card in it. I am running kernel 2.6.5-1.358 with all of the updates as of today.
I am a bit confused (understatement)
I just lost ethernet connectivity and had to power cycle the laptop. I was getting so many messages written to /var/log/messages that the system was unresponsive. I was using XMMS listening to radio station.
Messages start with: May 11 10:10:31 mktg6nt kernel: spurious 8259A interrupt: IRQ7. May 11 10:41:27 mktg6nt kernel: eth1: error -110 reading info frame. Frame dropped. May 11 10:41:27 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:29 mktg6nt last message repeated 349 times May 11 10:41:29 mktg6nt kernel: hermes @ MEM 0x21ea1000: Timeout waiting for command completion. May 11 10:41:29 mktg6nt kernel: hermes @ MEM 0x21ea1000: Error -16 issuing command. May 11 10:41:29 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:30 mktg6nt last message repeated 63 times May 11 10:41:30 mktg6nt kernel: eth1: Ereth1: Error -110 writing Tx descriptor to BAP May 11 10:41:30 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:31 mktg6nt last message repeated 81 times May 11 10:41:31 mktg6nt kernel: eth1: Error -110 writing Tx eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:31 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:31 mktg6nt last message repeated 81 times May 11 10:41:31 mktg6nt kernel: eth1: Error -110 writing Tx eth1: Error -110 writing Tx descriptor to BAP
What I am really confused about are the following output from dmesg.
eth0: Station identity 001f:0009:0001:0004 eth0: Looks like an Intersil firmware version 1.4.9 eth0: Ad-hoc demo mode supported eth0: IEEE standard IBSS ad-hoc mode supported eth0: WEP supported, 104-bit key eth0: MAC address 00:02:6F:04:64:6A eth0: Station name "Prism I" eth0: ready 8139too Fast Ethernet driver 0.9.27 divert: allocating divert_blk for eth1 eth1: RealTek RTL8139 at 0x3000, 00:02:3f:8f:19:0e, IRQ 10 eth1: Identified 8139 chip type 'RTL-8100B/8139D'
BUT I have this from ifconfig:
mktg6nt: ifconfig -a eth1 Link encap:Ethernet HWaddr 00:02:6F:04:64:6A inet addr:192.9.200.42 Bcast:192.9.200.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4129 errors:0 dropped:0 overruns:0 frame:0 TX packets:1028 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:826960 (807.5 Kb) TX bytes:177917 (173.7 Kb) Interrupt:11 Base address:0x8000 Memory:e0500000-e0500fff
and in my modprobe.conf: alias eth0 8139too alias eth1 orinoco_pci
I am writting this with my laptop, so it came back up clean. I just do not understand the differences in the eth0/eth1 being reversed in the dmesg output from the ifconfig output.
Should I change the modprobe.conf to have the orinoco_pci aliased to eth0 and the builtin 8139too aliased to eth0?
What is the 8259A interupt? It seems like the builtin sound card.
Thanks.
Brian Millett wrote:
I am writting this with my laptop, so it came back up clean. I just do not understand the differences in the eth0/eth1 being reversed in the dmesg output from the ifconfig output.
The exact same thing happens on my Latitude C400. Sometimes it gets it right, sometimes it's flipped. In the end, it works as long as I leave it alone.
Should I change the modprobe.conf to have the orinoco_pci aliased to eth0 and the builtin 8139too aliased to eth0?
I wouldn't touch it; I tried messing around with it a bit and it confused redhat-network-config.
-- vh
i have a similar problem with a sharp actius um32w with a RealTek RTL8139 and an Intersil Corporation|Prism 2.5 Wavelan chipset' wireless card (see my message on 8-may to fedora-test-list for details). using stock kernels the wireless card is configured as eth0 and the ethernet card as eth1. then it configures them both again and confuses eth0 and eth1. kudzu then tries to configure the wireless card as eth2, redhat-network-config is totally confused. the ethernet card is working fine, the wireless card is not functioning at all. problems started with 2.6.5 kernels as best i can recall but i wiped out all the kernels before 2.6.5-1.327 to make space so i can't be totally sure.
Brian Millett wrote:
Hello, I have a toshiba laptop with a miniPCI EL-2511MP PLUS 802.11/b card in it. I am running kernel 2.6.5-1.358 with all of the updates as of today.
I am a bit confused (understatement)
I just lost ethernet connectivity and had to power cycle the laptop. I was getting so many messages written to /var/log/messages that the system was unresponsive. I was using XMMS listening to radio station.
Messages start with: May 11 10:10:31 mktg6nt kernel: spurious 8259A interrupt: IRQ7. May 11 10:41:27 mktg6nt kernel: eth1: error -110 reading info frame. Frame dropped. May 11 10:41:27 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:29 mktg6nt last message repeated 349 times May 11 10:41:29 mktg6nt kernel: hermes @ MEM 0x21ea1000: Timeout waiting for command completion. May 11 10:41:29 mktg6nt kernel: hermes @ MEM 0x21ea1000: Error -16 issuing command. May 11 10:41:29 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:30 mktg6nt last message repeated 63 times May 11 10:41:30 mktg6nt kernel: eth1: Ereth1: Error -110 writing Tx descriptor to BAP May 11 10:41:30 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:31 mktg6nt last message repeated 81 times May 11 10:41:31 mktg6nt kernel: eth1: Error -110 writing Tx eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:31 mktg6nt kernel: eth1: Error -110 writing Tx descriptor to BAP May 11 10:41:31 mktg6nt last message repeated 81 times May 11 10:41:31 mktg6nt kernel: eth1: Error -110 writing Tx eth1: Error -110 writing Tx descriptor to BAP
What I am really confused about are the following output from dmesg.
eth0: Station identity 001f:0009:0001:0004 eth0: Looks like an Intersil firmware version 1.4.9 eth0: Ad-hoc demo mode supported eth0: IEEE standard IBSS ad-hoc mode supported eth0: WEP supported, 104-bit key eth0: MAC address 00:02:6F:04:64:6A eth0: Station name "Prism I" eth0: ready 8139too Fast Ethernet driver 0.9.27 divert: allocating divert_blk for eth1 eth1: RealTek RTL8139 at 0x3000, 00:02:3f:8f:19:0e, IRQ 10 eth1: Identified 8139 chip type 'RTL-8100B/8139D'
BUT I have this from ifconfig:
mktg6nt: ifconfig -a eth1 Link encap:Ethernet HWaddr 00:02:6F:04:64:6A inet addr:192.9.200.42 Bcast:192.9.200.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4129 errors:0 dropped:0 overruns:0 frame:0 TX packets:1028 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:826960 (807.5 Kb) TX bytes:177917 (173.7 Kb) Interrupt:11 Base address:0x8000 Memory:e0500000-e0500fff
and in my modprobe.conf: alias eth0 8139too alias eth1 orinoco_pci
I am writting this with my laptop, so it came back up clean. I just do not understand the differences in the eth0/eth1 being reversed in the dmesg output from the ifconfig output.
Should I change the modprobe.conf to have the orinoco_pci aliased to eth0 and the builtin 8139too aliased to eth0?
What is the 8259A interupt? It seems like the builtin sound card.
Thanks.