Hi,
I install a guest Fedora inside the host Fedora. When I use the
service xend status
to check the status of xend. It shows xend is running.
However when I use
xm create xen1
to start the guest domain xen1, it failed. The corresponding file xen1 is in /etc/xen/xen1. The error msg is as follows:
[root@phillis xen]# xm create xen1 Using config file "./xen1". Going to boot Fedora Core (2.6.19-1.2911.6.5.fc6xen) kernel: /vmlinuz-2.6.19-1.2911.6.5.fc6xen initrd: /initrd-2.6.19-1.2911.6.5.fc6xen.img Error: Device 0 (vif) could not be connected. Could not find bridge device xenbr1
I found the following line in file /etc/xen/xen1, vif = [ 'mac=00:16:3e:5c:5c:31, bridge=xenbr1', ]
Why device 0 couldn't be connected? I don't know the usage of the bridge device, xenbr1.
Anybody has similar problem ? Or know how to slove this problem? THanks.
Best Angel
taoj2@cs.rpi.edu wrote:
Hi,
I install a guest Fedora inside the host Fedora. When I use the
service xend status
to check the status of xend. It shows xend is running.
However when I use
xm create xen1
to start the guest domain xen1, it failed. The corresponding file xen1 is in /etc/xen/xen1. The error msg is as follows:
[root@phillis xen]# xm create xen1 Using config file "./xen1". Going to boot Fedora Core (2.6.19-1.2911.6.5.fc6xen) kernel: /vmlinuz-2.6.19-1.2911.6.5.fc6xen initrd: /initrd-2.6.19-1.2911.6.5.fc6xen.img Error: Device 0 (vif) could not be connected. Could not find bridge device xenbr1
I found the following line in file /etc/xen/xen1, vif = [ 'mac=00:16:3e:5c:5c:31, bridge=xenbr1', ]
Why device 0 couldn't be connected? I don't know the usage of the bridge device, xenbr1.
Anybody has similar problem ? Or know how to slove this problem? THanks.
Best Angel
when you do an ifconfig do you see a xenbr1 or a xenbr0?
-Mike
Hi there I have installed Xen virtual machine in Red Hat Enterprise 5 named virtpc1. Now can you tell me how can I get more copy of the virtpc1 named virtpc2, virtpc3 etc ?
What I have done so far ,
I copied the virtpc1 as virtpc2 and virtpc3 in /etc/xen , changed the hostname and file name in config respective in /etc/xen also I copied the disk file in /opt/virtpc1 as virtpc2 and virtpc3.
When I type # xm create virtpc1 , it creates domain virtpc1 fine and running fine. But when I type xm create virtpc2 it fails but if I type xm list and I can see two more domains created by the named virtpc1 virtpc1 , same name twice , it supposed to be virtpc1 and virtpc2.
Any solution please ?
Regards selim
Selim Jahangir wrote:
Hi there I have installed Xen virtual machine in Red Hat Enterprise 5 named virtpc1. Now can you tell me how can I get more copy of the virtpc1 named virtpc2, virtpc3 etc ?
What I have done so far ,
I copied the virtpc1 as virtpc2 and virtpc3 in /etc/xen , changed the hostname and file name in config respective in /etc/xen also I copied the disk file in /opt/virtpc1 as virtpc2 and virtpc3.
When I type # xm create virtpc1 , it creates domain virtpc1 fine and running fine. But when I type xm create virtpc2 it fails but if I type xm list and I can see two more domains created by the named virtpc1 virtpc1 , same name twice , it supposed to be virtpc1 and virtpc2.
Any solution please ?
uuid should be uniq for each guest. Use uuidgen and replace the uuid= parameter on the second and third guest.
Regards selim
-- Fedora-xen mailing list Fedora-xen@redhat.com https://www.redhat.com/mailman/listinfo/fedora-xen