Hello,
I am trying to setup Outlook Express (email client to setup mail accounts)
, when I try to send mails outside my domain like
@mydomain.com<http://mydomain.com>ie to yahoo or gmail or hotmail, I get this error
message
"The message could not be sent because one of the recipients was> rejected
by the server. The rejected e-mail address was 'janu(a)cs.unm.edu'. Subject
'test',
Account:'mail.relate24seven.com
<
http://mail.relate24seven.com><
http://mail.relate24seven.com>> ',> Server:
'65.103.191.30<http://65.103.191.30><
http://65.103.191.30>';, Protocol: SMTP, Server> Response: '550 5.7.1>
<
janu@cs.unm.edu>... Relaying denied', Port: 25, Secure(SSL): No,> Server
Error: 550, Error Number: 0x800CCC79.
When I use pine on the server , I can send mails to everyone and recieve
from everyone.
I can send mails to @relate24seven.com
<
http://relate24seven.com> in OE
.If this is an OE problem , then I have the same problem with Thunderbird
mail client too ; while sending emails it prompts fro password I type in the
same password as used for incoming mail server which is the same as the
outgoing one , and it does not work
The following is the iptable file output :
# Firewall configuration written by system-config-securitylevel
# Manual customization of this file is not recommended.
*filter
:INPUT ACCEPT [0:0]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [0:0]
:RH-Firewall-1-INPUT - [0:0]
-A INPUT -j RH-Firewall-1-INPUT
-A FORWARD -j RH-Firewall-1-INPUT
-A RH-Firewall-1-INPUT -i lo -j ACCEPT
-A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT
-A RH-Firewall-1-INPUT -p 50 -j ACCEPT
-A RH-Firewall-1-INPUT -p 51 -j ACCEPT
-A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251<http://224.0.0.251>-j
ACCEPT
-A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT
-A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 21 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 23 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 25 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 110 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 143 -j
ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 5901 -j
ACCEPT
-A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited
COMMIT
When I try to do nmap localhost it shows this :
PORT STATE SERVICE
21/tcp open ftp
22/tcp open ssh
25/tcp open smtp
80/tcp open http
110/tcp open pop3
111/tcp open rpcbind
113/tcp open auth
143/tcp open imap
443/tcp open https
631/tcp open ipp
3306/tcp open mysql
5900/tcp open vnc
10000/tcp open snet-sensor-mgmt
But when I try nmap 65.103.191.30 <
http://65.103.191.30>, it shows this :
(The 1658 ports scanned but not shown below are in state: closed)
PORT STATE SERVICE
23/tcp open telnet
80/tcp open http
The following is the maillog output :
May 4 11:08:10 relate24seven sendmail[7908]: j44I89Gq007908:
ruleset=check_rcpt, arg1=<janu(a)cs.unm.edu>,
relay=nhpsde.heritage.unm.edu<http://nhpsde.heritage.unm.edu>[
64.106.114.26 <
http://64.106.114.26>], reject=550 5.7.1 <janu@cs.unm.edu>...
Relaying denied
May 4 11:08:10 relate24seven sendmail[7908]: j44I89Gr007908:
ruleset=check_rcpt, arg1=<josh(a)relate247.com>,
relay=nhpsde.heritage.unm.edu<http://nhpsde.heritage.unm.edu>[
64.106.114.26 <
http://64.106.114.26>], reject=550 5.7.1
<josh@relate247.com>...
Relaying denied
Any help with this?