Affects Skylake and Kabylake so far, I'm not sure how extensive it is
within each series, but as F31 has rebased to 5.4 I thought I'd give a
heads up. It's actually somewhat rare, I have an npm+electron chat app
that seems to hit this way more often than say Firefox (and I'm not
chatting near as much as I'm webbing).
[drm:gen8_reset_engines [i915]] *ERROR* rcs0 reset request timed out
If you hit it, revert to 5.3.18 and if you want cc to the bug report
with CPU model. Another idea is to use a current 5.5.0rc, it's fixed
there but the backport is giving upstream devs some grief so I'm not
sure when it's going to get fixed in 5.4. I think part of the delay is
also the two holidays falling on Wednesdays :D
When installing, I had a Dell monitor attached to an nvidia graphics card via HDMI and that was working fine. I
installed the nvidia drivers for this.
I now want to use an old ViewSonic monitor as a second monitor so I plugged it into the on-board VGA port and booted.
The ViewSonic monitor is now the only monitor working. I adjusted the settings to make the display useable (Settings ->
Devices -> Displays) but only the ViewSonic monitor is listed here.
Google has led me to try this:
simon@hedgehog ~]$ lspci | grep -i VGA
00:02.0 VGA compatible controller: Intel Corporation UHD Graphics 630 (Desktop 9 Series) (rev 02)
01:00.0 VGA compatible controller: NVIDIA Corporation GP108 [GeForce GT 1030] (rev a1)
[simon@hedgehog ~]$ xrandr -q
Screen 0: minimum 320 x 200, current 1600 x 1200, maximum 16384 x 16384
HDMI-1 disconnected (normal left inverted right x axis y axis)
DP-1 connected primary 1600x1200+0+0 (normal left inverted right x axis y axis) 432mm x 324mm
1400x1050 74.87 59.98
1280x1024 75.02 60.02
1024x768 75.03 70.07 60.00
800x600 72.19 75.00 60.32 56.25
640x480 75.00 72.81 66.67 59.94
** Note that there is an HDMI connector on the motherboard as well so I am not sure if HDMI-1 here refers to that.
I tried this:
[simon@hedgehog ~]$ xrandr --output HDMI-1 --auto --right-of DP-1
... but there was no output and nothing changed.
I would like to end up with a separate desktop on each monitor.
Any help gratefully received.
I have a lenovo x1 carbon (2014 I believe).
00:02.0 VGA compatible controller: Intel Corporation HD Graphics 5500 (rev
This is F31
Using X, KDE.
(Also newer kde builds from name=Copr repo for kde owned by zawertun)
Detecting plug/unplug hdmi is unreliable. The only reliable way to get it
to work is switch to VT, then switch back to X.
Same for sleep on lid close. Only seems to work reliably if I switch to VT.
Over the years it seems to have gone from being somewhat unreliable, to
about 100% reliable, to now being quite unreliable.
I'm receiving emails from a lot of customers that use Microsoft
Sometime I receive the emails with winmail.dat attached.
Evolution is unable to display it correctly.
If I use ktnef to open the attachement I have other problems.
Some of the problems found on ktnef are solved with ytnef.
I had look at google solutions and I found that evolution can be
compiled with tnef plugin enabled, but it seems Fedora don't do it.
Can I understand why, and if there is a simple way to obtain tnef
support working on the box with Evolution?
I'm using Fedora 31 with Evolution 3.34.2
I bought this laptop over Christmas:
ASUS VivoBook Pro N705FD Notebook, 17.3" FHD Display, Intel Core
i7-8565U Upto 4.60GHz, 32GB RAM, 1TB SSD + 1TB HDD, NVIDIA GeForce GTX
1050, HDMI, Card Reader, Wi-Fi, Bluetooth, Windows 10 Pro
And I installed Fedora 31 on it.
The HDMI port drives a second monitor fine but the USB-C port will not.
I can plug an external drive into the USB-C port and it mounts it fine,
however I would like to drive an additional monitor with it.
When I plug an external monitor into the USB-C port I usually see
something like this via dmesg:
[100335.446405] usb 1-3: new high-speed USB device number 11 using xhci_hcd
[100335.919043] usb 1-3: New USB device found, idVendor=2109,
idProduct=0100, bcdDevice= 6.03
[100335.919046] usb 1-3: New USB device strings: Mfr=1, Product=2,
[100335.919048] usb 1-3: Product: USB-C dongle
[100335.919050] usb 1-3: Manufacturer: VIA Technologies Inc.
[100335.919051] usb 1-3: SerialNumber: 0000000000000001
[100340.101375] usb usb2-port3: Cannot enable. Maybe the USB cable is bad?
[100344.156355] usb usb2-port4: Cannot enable. Maybe the USB cable is bad?
Also here is the output of an lspci:
00:00.0 Host bridge: Intel Corporation Coffee Lake HOST and DRAM
Controller (rev 0b)
00:02.0 VGA compatible controller: Intel Corporation UHD Graphics 620
00:04.0 Signal processing controller: Intel Corporation Xeon E3-1200
v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem (rev 0b)
00:08.0 System peripheral: Intel Corporation Xeon E3-1200 v5/v6 /
E3-1500 v5 / 6th/7th/8th Gen Core Processor Gaussian Mixture Model
00:12.0 Signal processing controller: Intel Corporation Cannon Point-LP
Thermal Controller (rev 30)
00:14.0 USB controller: Intel Corporation Cannon Point-LP USB 3.1 xHCI
Controller (rev 30)
00:14.2 RAM memory: Intel Corporation Cannon Point-LP Shared SRAM (rev 30)
00:14.3 Network controller: Intel Corporation Cannon Point-LP CNVi
[Wireless-AC] (rev 30)
00:15.0 Serial bus controller [0c80]: Intel Corporation Cannon Point-LP
Serial IO I2C Controller #0 (rev 30)
00:15.1 Serial bus controller [0c80]: Intel Corporation Cannon Point-LP
Serial IO I2C Controller #1 (rev 30)
00:16.0 Communication controller: Intel Corporation Cannon Point-LP MEI
Controller #1 (rev 30)
00:17.0 SATA controller: Intel Corporation Cannon Point-LP SATA
Controller [AHCI Mode] (rev 30)
00:1c.0 PCI bridge: Intel Corporation Cannon Point-LP PCI Express Root
Port #1 (rev f0)
00:1c.4 PCI bridge: Intel Corporation Cannon Point-LP PCI Express Root
Port #5 (rev f0)
00:1d.0 PCI bridge: Intel Corporation Cannon Point-LP PCI Express Root
Port #9 (rev f0)
00:1e.0 Communication controller: Intel Corporation Device 9da8 (rev 30)
00:1e.2 Serial bus controller [0c80]: Intel Corporation Device 9daa (rev 30)
00:1f.0 ISA bridge: Intel Corporation Cannon Point-LP LPC Controller
00:1f.3 Audio device: Intel Corporation Cannon Point-LP High Definition
Audio Controller (rev 30)
00:1f.4 SMBus: Intel Corporation Cannon Point-LP SMBus Controller (rev 30)
00:1f.5 Serial bus controller [0c80]: Intel Corporation Cannon Point-LP
SPI Controller (rev 30)
02:00.0 3D controller: NVIDIA Corporation GP107M [GeForce GTX 1050
Mobile] (rev a1)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 15)
Thanks in advance...
After updating a Fedora 30 system to 31, I can't install scala:
# dnf module list scala
Last metadata expiration check: 0:31:21 ago on Mon 06 Jan 2020 13:31:04
Name Stream Profiles
scala 2.10 [e] default
A hybrid functional/object-oriented language for the JVM
Hint: [d]efault, [e]nabled, [x]disabled, [i]nstalled
# dnf install scala
Last metadata expiration check: 0:31:32 ago on Mon 06 Jan 2020 13:31:04
All matches were filtered out by modular filtering for argument: scala
Error: Unable to find a match: scala
If I try to install a package that depends on scala:
# dnf install ant-scala
Last metadata expiration check: 0:32:13 ago on Mon 06 Jan 2020 13:31:04
Problem: package ant-scala-2.10.6-16.fc31.noarch requires scala =
2.10.6-16.fc31, but none of the providers can be installed
- conflicting requests
- package scala-2.10.6-16.fc31.noarch is filtered out by modular filtering
(try to add '--skip-broken' to skip uninstallable packages)
How can I find out why scalar is being "filtered out by modular filtering"?
This is an updated fc30->fc31 system. A clean install of fc31 will install
Norman Gaywood, Computer Systems Officer
School of Science and Technology
University of New England
Armidale NSW 2351, Australia
Phone: +61 (0)2 6773 2412 Mobile: +61 (0)4 7862 0062
Please avoid sending me Word or Power Point attachments.
I have a new gig, the client runs office365 (ugh). I did the new email
account in thunderbird, used "outlook.office365.com" as the incoming
IMAP server and I can receive emails but not send.
I used another account for sending (SMTP), since "outlook.office365.com"
did not work but now all my sent items go to ther junk mail (ultimately
coming from another domain), and I also find that if I set it to
automatically bcc my office635 email for sent messages, they dont show
Thoughts? Is there a better way to interact with office365?
Thanks in advance
Seems strange after the Kernel of the week updates that there have been
no updates for Fedora 30.
Perhaps everyone is on holiday? :)
Just seems unnatural...
Remember do not since any thing with the year abbreviated.
January 3, 20
Is too easy to change to 2019 or some earlier year or later (2022) and
cause you challenges. It has been 101 years since the last time this
happened, and few of us were around then to deal with it. :)
I have my old laptop, HP ProBook 4410s, it is 32-bit processor with 1GB
memory. I installed F30 and now I want to install Anaconda. Unfortunately,
I could not find 32-bit version of it. Please help me.