Linux version 2.6.15-1.1863_FC5 (bhcompile@ls20-bc1-13.build.redhat.com) (gcc ve rsion 4.1.0 20060117 (Red Hat 4.1.0-0.15)) #1 Thu Jan 19 19:17:58 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. Using x86 segment limits to approximate NX protection DMI 2.2 present. ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC disabled (-2); pass 'lapic' to re-enable. Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Built 1 zonelists Kernel command line: ro root=LABEL=/ console=ttyS0,115200n8 console=tty Enabling fast FPU save and rest Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c03d8000 soft=c03d7000 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1670.785 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 514700k/524224k available (1929k kernel code, 9008k reserved, 777k data, 176k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3346.04 BogoMIPS (lpj=6692090) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) CPU: AMD Athlon(tm) XP 2000+ stepping 02 Checking 'hlt' instruction... OK. ACPI: setting ELCR to 0200 (from 1e20) checking if image is initramfs... it is Freeing initrd memory: 767k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb3b0, last bus=2 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 4000-407f claimed by vt8235 PM PCI quirk: region 5000-500f claimed by vt8235 SMB ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15) ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled. ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled. ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled. ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:01: ioport range 0x4000-0x407f could not be reserved pnp: 00:01: ioport range 0x5000-0x500f has been reserved PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: e0000000-e1ffffff PREFETCH window: d8000000-dfffffff PCI: Bus 2, cardbus bridge: 0000:00:0a.0 IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 30000000-31ffffff MEM window: 32000000-33ffffff ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 10 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1137936050.676:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 8928DF366D0286DA - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop regist io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Fan [FAN] (on) ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Thermal Zone [THRM] (43 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA KT400/KT400A/KT600 chipset agpgart: AGP aperture is 128M @ 0xd0000000 PNP: PS/2 Controller [PNP0303:PS2K] at PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled ˙serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 11 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdc:DMA, hdd:DMA hda: SAMSUNG SP8004H, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: SAMSUNG CD-R/RW SW-252B, ATAPI CD/DVD-ROM drive hdd: ATAPI DVD DUAL 8X4X12, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33) ide-floppy driver 0.99.newide ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 Yenta: CardBus bridge found at 0000:00:0a.0 [1154:030a] Yenta: ISA IRQ mask 0x0000, PCI irq 10 Socket status: 30000810 usbcore: registered new driver libusual usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 IP route cache hash table entries: 8192 (order: 3, 32768 bytes) TCP established hash table entries: 32768 (order: 7, 524288 bytes) TCP bind hash table entries: 32768 (order: 7, 655360 bytes) TCP: Hash tables configured (established 32768 bind 32768) TCP reno registered TCP bic registered Initializing IPsec NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Processor cpuid 662 not supported Using IPI Shortcut mode ACPI wakeup devices: PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1 LPT1 ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 176k freed Write protecting the kernel read-only data: 356k input: AT Translated Set 2 keyboard as /class/input/input0 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. pccard: PCMCIA card inser SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks Unable to handle kernel NULL pointer dereference at virtual address 000000fc printing eip: *pde = 1ef5b067 Oops: 0002 [#1] last sysfs file: /devices/pci0000:00/0000:00:11.5/modalias Modules linked in: parport_pc parport floppy nvram orinoco_cs orinoco hermes hos tap_cs hostap ieee80211_crypt stradis compat_ioctl32 ehci_hcd ohci1394 ieee1394 uhci_hcd snd_via82xx gameport snd_ac97_codec snd_ac97_bus snd_seq_dummy snd_seq_ oss snd_seq_midi_event snd_seq snd_pcm_oss snd_mixer_oss dvb_ttpci l64781 saa714 6_vv snd_pcm video_buf saa7146 v4l1_compat snd_timer v4l2_common snd_page_alloc videodev ves1820 snd_mpu401_uart snd_rawmidi i2c_viapro stv0299 snd_seq_device v ia_ircc dvb_core tda8083 snd irda stv0297 sp8870 ves1x93 ttpci_eeprom i2c_core v ia_rhine mii soundcore crc_ccitt ext3 jbd CPU: 0 EIP: 0060:[] Not tainted VLI EFLAGS: 00010246 (2.6.15-1.1863_FC5) EIP is at stradis_probe+0x5ba/0xa81 [stradis] eax: 00000000 ebx: e09f20e0 ecx: 00000000 edx: df23ccf0 esi: e09f1b2c edi: e09f2540 ebp: e09f20e0 esp: df074d70 ds: 007b es: 007b ss: 0068 Process modprobe (pid: 899, threadinfo=df074000 task=df23ccf0) Stack: <0>dfcf607c 00000000 00000000 00000001 dead4ead ffffffff ffffffff 0000000 1 dead4ead ffffffff ffffffff 00000001 dead4ead ffffffff ffffffff 00000001 dead4ead ffffffff ffffffff 00000001 dead4ead ffffffff ffffffff e09f190c Call Trace: [] __driver_attach+0x0/0x8b [] driver_probe_device+0x42/0x8b [] __driver_attach+0x6 3/0x8b [] bus_for_each_dev+0x33/0x55 [] driver_attach+0x11/0x1 3 [] __driver_attach+0x0/0x8b [] bus_add_driver+0x64/0xfd [] __pci_register_driver+0x82/0xa4 [] stradis_init+0x1a /0x2f [stradis] [] sys_init_module+0x137c/0x150e [] ieee80211_crypt_nul l_init+0x0/0x6 [ieee80211_crypt] [] do_sync_read+0xb8/0xf3 [] __mutex_unlock_slowpath+0x1c3/0x1c8 [] do_sync_read+ 0x0/0xf3 [] vfs_read+0x9f/0x13e [] sys_read+0x3c/0x63 [] syscall_call+0x7/0xb <0>Code: c4 10 e9 df 04 00 00 8b 04 24 8b 98 74 01 00 00 31 c0 b9 18 01 00 00 89 df f3 ab c7 83 7c 02 00 00 00 00 00 00 8b 83 0c 03 00 00 80 fc 00 00 00 00 00 ff ff b8 00 f0 ff ff 21 e0 f7 40 14 00 Continuing in 1 seconds. <1>Unable to handle kernel NULL pointer dereference at virtual address 00000000 printing eip: c0188fff *pde = 1edf3067 Oops: 0000 [#2] last sysfs file: /devices/pci0000:00/0000:00:11.5/modalias Modules linked in: parport_pc parport floppy nvram orinoco_cs orinoco hermes hos tap_cs hostap ieee80211_crypt stradis compat_ioctl32 ehci_hcd ohci1394 ieee1394 uhci_hcd snd_via82xx gameport snd_ac97_codec snd_ac97_bus snd_seq_dummy snd_seq_ oss snd_seq_midi_event snd_seq snd_pcm_oss snd_mixer_oss dvb_ttpci l64781 saa714 6_vv snd_pcm video_buf saa7146 v4l1_compat snd_timer v4l2_common snd_page_allo videodev ves1820 snd_mpu401_uart snd_rawmidi i2c_viapro stv0299 snd_seq_device v ia_ircc dvb_core tda8083 snd irda stv0297 sp8870 ves1x93 ttpci_eeprom i2c_core v ia_rhine mii soundcore crc_ccitt ext3 jbd CPU: 0 EIP: 0060:[] Not tainted VLI EFLAGS: 00010246 (2.6.15-1.1863_FC5) EIP is at sysfs_lookup+0x30/0x1ac eax: 00000000 ebx: dee9a1e0 ecx: df0d5f10 edx: 00000004 esi: 00000000 edi: dee9a250 ebp: ded19348 esp: df0d5dd8 ds: 007b es: 007b ss: 0068 Process udevd (pid: 1227, threadinfo=df0d5000 task=df13f1f0) Stack: <0>ded1937c ffffffff c034b840 dee9a1e0 df272b80 df272c00 c015fe39 df0d5e5 0 df0d5e44 df0d5f10 dffe5be0 baf3f719 df272b80 ded5101e df0d5f10 c016198f 00000000 ded51024 00000000 00000000 00000000 000200d2 c0347ce8 00000000 Call Trace: [] do_lookup+0xb2/0x14d [] __link_path_walk+0x821/0xc65 [] link_path_walk+0x47/ 0xb9 [] do_path_lookup+0x1ee/0x228 [] __user_walk_fd+0x29/0x 3a [] vfs_lstat_fd+0x12/0x39 [] sys_lstat64+0xf/0x23 [] do_page_fault+0x189/0x51d [] do_page_fault+0x0/0x51d [] syscall_call+0x7/0xb <0>Code: ec 08 89 d3 8b 42 24 8b 40 60 89 04 24 8b 68 0c e9 6c 01 00 00 f6 45 18 2c 0f 84 5f 01 00 00 89 e8 e8 ca ed ff ff 89 c6 8b 7b 30 ae 75 08 84 c0 75 f8 31 c0 eb 04 19 c0 0c 01 85 c0 0f 85 3b Continuing in 1 seconds. BUG: udevd/1227, lock held at task exit time! [df272c00] {inode_init_once} .. held by: udevd: 1227 [df13f1f0, 118] ... acquired at: do_lookup+0x78/0x14d usb 1-2: new high speed USB device using ehci_hcd and address 3 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000d100808e7e2e] usb 1-2.4: new high speed USB device using ehci_hcd and address 5 usb 1-2.4: configuration #1 chosen from 1 choice SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. Vendor: Generic Model: CF Rev: 1.6E Type: Direct-Access ANSI SCSI revision: 00 Vendor: Generic Model: MS Rev: 1.6E Type: Direct-Access ANSI SCSI revision: 00 Vendor: Generic Model: MMC/SD Rev: 1.6E Type: Direct-Access ANSI SCSI revision: 00 Vendor: Generic Model: SM Rev: 1.6E Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete sd 0:0:0:0: Attached scsi removable disk sda sd 0:0:0:1: Attached scsi removable disk sdb sd 0:0:0:2: Attached scsi removable disk sdc sd 0:0:0:3: Attached scsi removable disk sdd