Re: sil3114
by Si Jones
Am writing this again as the post has dissopeared.
If there is support for the Sil3114 i dont think it has been compiled
into the kernel in FC2 T3 as when i boot i get it saying no hard drives
found and if i try and specifiy the module to load i can't see sil3114
to choose from?
Has anyone else done anything with this? a work around?
19 years, 12 months
FC2 problems with Fujitsu Lifebook C2240
by Martin Robb
I just received a Lifebook C2240 to replace my older C series laptop
(which was running FC2 nicely). The install of FC2t3 on the C2240 ran
flawlessly, including the initial hard disk boot and all the way through
final setup. However, on all subsequent boots it dies utterly on the
boot (screen goes blank, no response to <ctrl><alt><del>, etc.). I
tried to go into interactive setup to get a better idea of where the
problem lies, but the failure is somewhere between the prompt for
interactive setup and the start of interactive setup.
I tried rolling back to FC2t2 -- same behavior. I tried FH9 and FC1 --
both work very nicely, so it seems isolated to FC2 (perhap a 2.6 kernel
problem?).
Marty
MartinRobb(a)ieee.org
PS: FWIW, here is the dmesg output under FC1 (sorry, rather long):
Linux version 2.4.22-1.2115.nptl (bhcompile(a)daffy.perf.redhat.com) (gcc
version 3.2.3 20030422 (Red Hat Linux 3.2.3-6)) #1 Wed Oct 29 15:42:51
EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001def0000 (usable)
BIOS-e820: 000000001def0000 - 000000001deff000 (ACPI data)
BIOS-e820: 000000001deff000 - 000000001df00000 (ACPI NVS)
BIOS-e820: 000000001df00000 - 000000001df80000 (usable)
BIOS-e820: 000000001df80000 - 000000001e000000 (reserved)
BIOS-e820: 000000002df80000 - 000000002e000000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 122752
zone(0): 4096 pages.
zone(1): 118656 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 FUJ ) @ 0x000f6880
ACPI: RSDT (v001 FUJ BRIE5 0x01040000 FUJ 0x00001000) @ 0x1defb455
ACPI: FADT (v001 FUJ BRIE5 0x01040000 FUJ 0x00001000) @ 0x1defef64
ACPI: BOOT (v001 FUJ BRIE5 0x01040000 FUJ 0x00001000) @ 0x1defefd8
ACPI: DSDT (v001 FUJ BRIE5 0x01040000 MSFT 0x0100000e) @ 0x00000000
Kernel command line: ro root=LABEL=/ hdc=ide-scsi rhgb
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 2791.107 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5570.56 BogoMIPS
Memory: 481368k/491008k available (1503k kernel code, 9184k reserved,
1110k data, 136k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebf9ff 00000000 00000000 00000000
CPU: Common caps: bfebf9ff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch(a)atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20031002
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd85e, last bus=3
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router ALI [10b9/1533] at 00:07.0
PCI: Found IRQ 11 for device 00:0c.3
PCI: Sharing IRQ 11 with 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.2
PCI: Sharing IRQ 11 with 00:0c.4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS3 at 0x02e8 (irq = 3) is a 16550A
PCI: Found IRQ 11 for device 00:03.0
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (10b9,5457,10cf,1130)
and the manufacturer and name of serial board or modem board
to serial-pci-info(a)lists.sourceforge.net.
register_serial(): autoconfig failed
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0f.0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1c00-0x1c07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1c08-0x1c0f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK6021GAS, ATA DISK drive
blk: queue c040cfc0, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA DVD-ROM SD-R6012, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117210240 sectors (60012 MB), CHS=7296/255/63, UDMA(100)
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 160k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 136k freed
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:13.0
usb-ohci.c: USB OHCI at membase 0xde858000, IRQ 11
usb-ohci.c: usb-00:13.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:13.1
PCI: Sharing IRQ 11 with 00:12.0
PCI: Sharing IRQ 11 with 01:05.0
usb-ohci.c: USB OHCI at membase 0xde85a000, IRQ 11
usb-ohci.c: usb-00:13.1, NEC Corporation USB (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:13.2
ehci_hcd 00:13.2: NEC Corporation USB 2.0
ehci_hcd 00:13.2: irq 11, pci mem de862400
usb.c: new USB bus registered, assigned bus number 3
ehci_hcd 00:13.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech(a)suse.cz>
hid-core.c: USB HID support drivers
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Adding Swap: 2096440k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 1010 $ Ben Collins <bcollins(a)debian.org>
PCI: Found IRQ 11 for device 00:0e.0
ohci1394_0: Unexpected PCI resource length of 1000!
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[dc013000-dc0137ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000e1002408d29]
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-R6012 Rev: 1F34
Type: CD-ROM ANSI SCSI revision: 02
IA-32 Microcode Update Driver: v1.11 <tigran(a)veritas.com>
microcode: CPU0 no microcode found! (sig=f29, pflags=4)
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
inserting floppy driver for 2.4.22-1.2115.nptl
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 00:11.0
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xdea21000, 00:0b:5d:2b:2f:d8, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 00:11.0
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xdea21000, 00:0b:5d:2b:2f:d8, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.3
PCI: Sharing IRQ 11 with 00:0c.4
PCI: Sharing IRQ 11 with 00:0c.2
PCI: Found IRQ 11 for device 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.3
PCI: Sharing IRQ 11 with 00:0c.4
PCI: Sharing IRQ 11 with 00:0c.2
PCI: Enabling device 00:0c.3 (0080 -> 0082)
PCI: Found IRQ 11 for device 00:0c.3
PCI: Sharing IRQ 11 with 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.4
PCI: Sharing IRQ 11 with 00:0c.2
PCI: Enabling device 00:0c.4 (0080 -> 0082)
PCI: Found IRQ 11 for device 00:0c.4
PCI: Sharing IRQ 11 with 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.3
PCI: Sharing IRQ 11 with 00:0c.2
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x408-0x40f
0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (3836 buckets, 30688 max) - 292 bytes per conntrack
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
visor.c: Untested USB device specified at time of module insertion
visor.c: Warning: This is not guaranteed to work
visor.c: Using a newer kernel is preferred to this method
visor.c: Adding Palm OS protocol 4.x support for unknown device: 0x54c/0x95
usbserial.c: USB Serial support registered for user specified device
with Palm 4.x protocols
usbserial.c: USB Serial support registered for Handspring Visor / Treo /
Palm 4.0 / Clie 4.x
usbserial.c: USB Serial support registered for Sony Clie 3.5
visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony Clie driver v1.7
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version
0.14.10h, 15:50:43 Oct 29 2003
PCI: Found IRQ 11 for device 00:04.0
trident: ALi Audio Accelerator found at IO 0x1400, IRQ 11
ac97_codec: AC97 Audio codec, id: 0x8384:0x7666 (SigmaTel STAC9750T)
ac97_codec: AC97 Audio codec, id: (Unknown)
PCI: Found IRQ 11 for device 00:04.0
gameport0: ALi Corporation M5451 PCI AC-Link Controller Audio Device at
pci00:04.0 speed 2593 kHz
i8253 count too high! resetting..
19 years, 12 months
Bugbuddy + OpenOffice
by Efthym
Hi all,
I'm trying to file a bug against OpenOffice 1.1.1-4, but the only entry in
BugBuddy is for OpenOffice Ximian. Is that where I should file it ?
Also, i checked if the bug exists in the OpenOffice buglist but couldn't
find it. Is there a list on Fedora that I should check as well ?
Thanks
--
Opera M2 Mail Client on FedoraCore2_Test3
19 years, 12 months
FC2T3: Cannot install to NCR/Symbios SCSI disks
by William Perkins
I tested Fedora Core 2 Test 1 when it came out and was able to get it to
install, but not without some problems unrelated with the current issue.
I have a Pentium III that has the following two SCSI cards (lspci):
0000:00:0b.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875J
(rev 04)
Subsystem: Diamond Multimedia Systems FirePort 40 SCSI Controller
Flags: bus master, medium devsel, latency 144, IRQ 11
I/O ports at b800 [size=256]
Memory at dd000000 (32-bit, non-prefetchable) [size=256]
Memory at dc800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
0000:00:0c.0 SCSI storage controller: LSI Logic / Symbios Logic 53c895
(rev 01)
Subsystem: Tekram Technology Co.,Ltd. DC-390U2W
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at b400 [size=256]
Memory at dc000000 (32-bit, non-prefetchable) [size=256]
Memory at db800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
When I try to install Fedora Core 2 Test 3, I get the boot prompt and the
kernel does load, but it never loads the NCR/Synbios SCSI driver. As a
result, it cannot find the CDROM to continue loading the system, and I am
sure it cannot the SCSI disks either. Both cards use the NCR53C8XX
driver. Neither the SYM53C8XX not the SYM53C8XX_2 drivers appear to work
with these cards.
I wanted to test the Test 3 release to see how well the 2.6 kernel would
work on my system. I have had problems trying to customize a 2.6 kernel.
I have been wondering if LVM and ALSA are working correctly with the 2.6
kernel.
Bill
----
William M. Perkins E-mail - wmp(a)grnwood.net
The Greenwood UNIX Systems Administration
Reston, Virginia (Solaris, Linux, HP-UX)
19 years, 12 months
autofs confusion
by Jason L Tibbitts III
I've just brought up a dual Opteron machine with FC2T3. This is my
first FC2 install, and everything seems to be going well except for
autofs.
Automounting is used extensively here for home directories and for
third-party apps in /usr/local. For often used applications we rsync
some directories from a central server. (One day I'll make RPMs out
of everything, but for now this is much easier.) So
/etc/auto_usr_local has lines like:
mathematica server:/export/stuff/mathematica-5.0
matlab localhost:/cache/pkg/matlab-6.5.1
This has worked fine for years now, from FC1 on back, with bind mounts
being used for the dirctories on localhost. Under FC2T3, however,
/usr/local/mathematica is there while /usr/local/matlab is not. This
appears in the logs:
Apr 29 12:52:28 compute08 automount[3112]: failed to mount /usr/local/matlab
I guess the move to autofs4 is involved but I don't know if what I'm
doing is expected not to work or if this is a real bug.
- J<
19 years, 12 months
tomcat and davenport
by Paul Bender
I have tomcat, apache and mod_jk2 running on the fedora core development
branch. All the examples run correctly, so I believe that everything is
installed and configured correctly.
I have downloaded and installed davenport from
<http://davenport.sourceforge.net/>. However, tomcat is unable to
correctly expand the davenport.war file. When I look at the log, I see
the error message:
HostConfig[localhost] Exception while expanding web application archive
davenport.war
Any ideas?
19 years, 12 months
Dell Latitude pp01l
by Quasar Jarosz
Well, the first machine that i attempted a clean FC2T3 install on was an
older Dell Latitude pp01l that i have over the weekend, to reinstall
windows on, for a co-worker.. i figured i'd toss Fedora on there, and
see how it goes.
First of all, it's nothing to great.. i thiks it's a 850mhz (though it
might be a 750mhz) Pentium III. It's got a 20 gig drive, and 128 megs of
ram. And some kidna ati card.. with a prime res of 1024x768.
The install went pretty well. No problems in Anaconda.. mouse worked,
keyboard worked, display worked fine too. I did note that it didn't
auto-eject the cd when it asked for another.. saw someone mention this
earlier.. not sure if it's a problem or just a change to the installer.
After the install, things started comming undone. I got the weird problem
with the graphical boot screen being broken in half and doubled up.. then
it would crash and the scree would go all white.. and i'd have to unplug
it. I used the trick someone mentioned before.. i booted knoppix and
removed all modes except the one tha worked from xorg, and then it booted
half-ok.. ended up i had to remove the graphical boot option from the
kernel flags in grub.. and then i had to edit the inittab and change it to
default to level 3. Oh, and i had to put the display driver on 'vesa'.. it
was on some ati driver and that wouldn't work either.. seemed to be what
was making it crash and turn white.
If i let it boot into init level 3, login, and run gdm, all goes well.
Also, oddly, if I log in, then type 'init 5', it seems to start up ok as
well. However, if i set the default back to init 5 and reboot, it goes
back into the graphical booter and crashes on boot.
Other than that, and being very slow (128 megs of ram...), all went well,
and nothing seems to be broken.. no xkb errors or anything.. touchpad and
erasor-head work great.
Tomorrow i install it on my laptop :)
19 years, 12 months
FC2T3 - LVM with RAID1 Failure
by Brian Hanks
Two attempts to install FC2T3 with LVM2 on top of RAID1 have both ended
in the same failure. This is the same disk layout that I've used
successfully in previous RH9, FC1, and FC2 installations.
The boot process dies right after it attempts to enable RAID. The error
is:
kernel BUG at drivers/block/cfq_iosched.c:404!
{trace info}
drivers/block/ll_rw_blk.c:1156: spin_lock(drivers/ide/ide.c:02347988)
already locked by drivers/block/ll_rw_blk.c/2164
Any thoughts?
Thanks,
-Brian
19 years, 12 months
FC2T2 - Unknown User error when shutting down via Main Menu
by David Kramer
I get an unknown user error that pops up when I attempt to close down or log
out from my main menu. After I click the error, It then drops me to my
login display where I then have to click shutdown again. I was thinking
this was a common error for FC2T2 but I havent been successful in finding
anything on the net.
Thanks,
David
19 years, 12 months