https://bugzilla.redhat.com/show_bug.cgi?id=834127
--- Comment #3 from Gary Gatling <gsgatlin(a)ncsu.edu> ---
Your comment was:
Ok. It seems there are problems....
Atrtempt #2 which is currently broken and unuseable. :(
http://install.linux.ncsu.edu/pub/yum/itecs/public/bumblebee/fedora17/spe...
http://install.linux.ncsu.edu/pub/yum/itecs/public/bumblebee/fedora17/SRP...
[gsgatlin@nom0047567 ~]$ optirun glxgears
ERROR: ld.so: object 'libdlfaker.so' from LD_PRELOAD cannot be preloaded:
ignored.
ERROR: ld.so: object 'librrfaker.so' from LD_PRELOAD cannot be preloaded:
ignored.
Running synchronized to the vertical refresh. The framerate should be
approximately the same as the monitor refresh rate.
341 frames in 5.0 seconds = 67.903 FPS
runs like crap. Admitedly I did not try rebooting yet.
So moving libdlfaker.so, at least in the way I did broke it. So I am
guessing It must be changed back in order to fix the app. ? How can I do this
in terms a noob would understand please. (If cmake puts it in the wrong place
how can I put it in the right place without "mv" in the specfile? since mv
breaks the app)
Also,
%if 0%{?rhel} == 6
%cmake28 -DTJPEG_INCLUDE_DIR=%{_includedir} \
-DTJPEG_LIBRARY=%{_libdir}/libturbojpeg.so \
-DVGL_USESSL=ON -DVGL_LIBDIR=%{_libdir} \
-DVGL_DOCDIR=%{_docdir}/%{name}-%{version}/ \
-DVGL_FAKELIBDIR=%{_libdir}/fakelib/ .
%else
%cmake -DTJPEG_INCLUDE_DIR=%{_includedir} \
-DTJPEG_LIBRARY=%{_libdir}/libturbojpeg.so \
-DVGL_USESSL=ON -DVGL_LIBDIR=%{_libdir} \
-DVGL_DOCDIR=%{_docdir}/%{name}-%{version}/ \
-DVGL_FAKELIBDIR=%{_libdir}/fakelib/ .
%endif
make %{?_smp_mflags}
results in this on rhel 6...
[gsgatlin@localhost specs]$ rpmbuild -ba VirtualGL.spec
Executing(%prep): /bin/sh -e /var/tmp/rpm-tmp.PIMqn5
+ umask 022
+ cd /home/gsgatlin/redhat/BUILD
+ LANG=C
+ export LANG
+ unset DISPLAY
+ cd /home/gsgatlin/redhat/BUILD
+ rm -rf VirtualGL-2.3.1
+ /bin/tar -xf -
+ /usr/bin/gzip -dc /home/gsgatlin/redhat/SOURCES/VirtualGL-2.3.1.tar.gz
+ STATUS=0
+ '[' 0 -ne 0 ']'
+ cd VirtualGL-2.3.1
+ /bin/chmod -Rf a+rX,u+w,g-w,o-w .
+ exit 0
Executing(%build): /bin/sh -e /var/tmp/rpm-tmp.ekgvFk
+ umask 022
+ cd /home/gsgatlin/redhat/BUILD
+ cd VirtualGL-2.3.1
+ LANG=C
+ export LANG
+ unset DISPLAY
+ %cmake28 -DTJPEG_INCLUDE_DIR=/usr/include
-DTJPEG_LIBRARY=/usr/lib64/libturbojpeg.so -DVGL_USESSL=ON
-DVGL_LIBDIR=/usr/lib64 -DVGL_DOCDIR=/usr/share/doc/VirtualGL-2.3.1/
-DVGL_FAKELIBDIR=/usr/lib64/fakelib/ .
/var/tmp/rpm-tmp.ekgvFk: line 33: fg: no job control
error: Bad exit status from /var/tmp/rpm-tmp.ekgvFk (%build)
RPM build errors:
Bad exit status from /var/tmp/rpm-tmp.ekgvFk (%build)
So I changed that back for RHEL 6.
Any advice appriciated.
--
You are receiving this mail because:
You are on the CC list for the bug.