Francesco,
in this special case BeamConstruct has no influence on it, it only depends on
CTI's emulation libraries.
Jim
On 21 November 2014 at 19:42 Francesco Perrucci
<francesco.perrucci(a)polito.it>
wrote:
It's right,
it's possibile to connect with ETH in beam construct?
2014-11-21 8:58 GMT+01:00 Jim Hart <openapc(a)gmail.com>:
> Because you were looking for an USB-connection ;-)
>
> > On 21 November 2014 at 17:50 Francesco Perrucci <
> francesco.perrucci(a)polito.it>
> > wrote:
> >
> >
> > Jim,
> >
> > yes it is, through a OEM I/O module! Why do you ask me this?
> >
> > Francesco
> >
> > 2014-11-21 7:09 GMT+01:00 Jim Hart <openapc(a)gmail.com>:
> >
> > > Francesco,
> > >
> > > isn't EC1000 the card that is controlled via Ethernet?
> > >
> > > Jim
> > >
> > > > On 20 November 2014 at 22:15 Francesco Perrucci <
> > > francesco.perrucci(a)polito.it>
> > > > wrote:
> > > >
> > > >
> > > > Jim,
> > > >
> > > > I think I found the solution. In the configuration wizard it's
> possible
> > > to
> > > > convert the correction table from .xml to a scanlab file.
> > > > So I'll try as possible and then I'll write you if it's
ok!!
> > > >
> > > > Maybe I need an USB connection to the EC1000, but the vendor never
> gives
> > > me
> > > > the right datasheet for the I/O module. So i'm writing him to
ask
> about
> > > > this.
> > > >
> > > > Thank you very much for your rapid answers.
> > > >
> > > > Francesco
> > > >
> > > > 2014-11-19 7:30 GMT+01:00 Jim Hart <openapc(a)gmail.com>:
> > > >
> > > > > Francesco,
> > > > >
> > > > > the .hex file is not really needed when you use UAPI-emulation,
> but you
> > > > > have to
> > > > > set it to satisfy the RTC4-plug-in. For the correction file
> situation
> > > is a
> > > > > bit
> > > > > different, I think you have to set it. But I don't know if
you
> have to
> > > > > specify
> > > > > the .xml file or a .ctb file converted out of the .xml file
from
> CTI.
> > > May
> > > > > be
> > > > > CTIs manual gives some information here?
> > > > >
> > > > > Jim
> > > > >
> > > > >
> > > > > > On 18 November 2014 at 21:27 Francesco Perrucci <
> > > > > francesco.perrucci(a)polito.it>
> > > > > > wrote:
> > > > > >
> > > > > >
> > > > > > Dear Jim,
> > > > > >
> > > > > > thank you for the rapid answer.
> > > > > >
> > > > > >
> > > > > > Now I understand that RTC4 work as a conversion for
EC1000.
> > > > > > But I've still difficulties to make the connection with
this
> card.
> > > > > >
> > > > > > First I would ask to you if it's needed an USB
connection.
> Because
> > > now I
> > > > > > can only connect the EC1000 through wi-fi or ethernet
connection.
> > > Looking
> > > > > > the electronic board I find a usb pin, so I think I could
use it
> if
> > > > > > necessary.
> > > > > >
> > > > > > I've already the RTC4DL file by the installation
package of
> Cambridge
> > > > > > Technology. I put this file into the Windows/SysWOW64 and
then I
> > > follow
> > > > > the
> > > > > > instruction of RTC emulation loader ( CTI installation
package )
> as
> > > you
> > > > > can
> > > > > > see in the attached pdf
> > > > > >
> > > > > > Then into BeamConstruct I select RTC4 in scanner
controller
> settings
> > > and
> > > > > > then into the configuration panel the sofware ask me for
the
> > > correction
> > > > > and
> > > > > > firmware files.
> > > > > >
> > > > > > So there's the problem. Into the zip dowloaded through
your
> link, I
> > > can
> > > > > > find the ctb (correction) and the hex (firmware) files, but
I
> think
> > > they
> > > > > > are related to Scanlab RTC4 controller.
> > > > > >
> > > > > > I need this file for my EC1000 controller, it is right?
Into the
> CTI
> > > > > > installation directory I've only .xml file both for
correction
> than
> > > for
> > > > > > firmware files, so i can't select them.
> > > > > >
> > > > > > Hope you can help me!!
> > > > > >
> > > > > > Thank you very much
> > > > > > Francesco
> > > > > >
> > > > > >
> > > > > >
> > > > > > 2014-11-18 6:59 GMT+01:00 Jim Hart
<openapc(a)gmail.com>:
> > > > > >
> > > > > > > Francesco,
> > > > > > >
> > > > > > > let me answer this in reverse order:
> > > > > > >
> > > > > > > > In addition to this, into the scanner section of
the project
> > > > > proprieties
> > > > > > > of
> > > > > > > > BeamConstruct I can't find the EC1000 entry.
It seems that
> the
> > > > > software
> > > > > > > > doesn't support it.
> > > > > > >
> > > > > > > When you are using CTIs RTC emulation you needto
select RTC4 in
> > > scanner
> > > > > > > controller settings. For BeamConstruct it acts like a
RTC4,
> > > conversion
> > > > > to
> > > > > > > EC1000
> > > > > > > is done by the emulation layer.
> > > > > > >
> > > > > > > > There's a software called RTC emulation
loader that ask me to
> > > browse
> > > > > into
> > > > > > > > the application's folder that contains the
RTC4DLL.dll in
> order
> > > to
> > > > > > > replace
> > > > > > > > it, but i can't find this file into the
OpenAPC folders.
> > > > > > >
> > > > > > > RTC4DL is a 3rd party software and therefore not
delivered with
> > > OpenAPC
> > > > > > > package.
> > > > > > > You can download it at
> > > > > > >
> > > > >
> > >
>
http://www.scanlab.de/en/-/products/control_boards/RTC_PC_interface#21065
> > > > > > >
> > > > > > > I'd recommend to put RTC4DLL somewhere into
Windows/System32 or
> > > > > > > Windows/SysWOW64
> > > > > > > (depending if you are using a 32 or 64 bit Windows).
> > > > > > >
> > > > > > > Jim
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > > _______________________________________________
> > > > > > > > openapc mailing list
> > > > > > > > openapc(a)lists.fedorahosted.org
> > > > > > > >
https://lists.fedorahosted.org/mailman/listinfo/openapc
> > > > > > >
> > > > > > >
> > > > > > > --
> > > > > > > Kind regards
> > > > > > >
> > > > > > > Jim Hart
> > > > > > >
> > > > > > >
http://www.lasermarkingsoftware.com
> > > > > > >
http://www.openapc.com
> > > > > > >
> > > > > > > Follow us at Twitter:
https://twitter.com/#!/openapc
> > > > > > > _______________________________________________
> > > > > > > openapc mailing list
> > > > > > > openapc(a)lists.fedorahosted.org
> > > > > > >
https://lists.fedorahosted.org/mailman/listinfo/openapc
> > > > > > >
> > > > >
> > > > >
> > > > > --
> > > > > Kind regards
> > > > >
> > > > > Jim Hart
> > > > >
> > > > >
http://www.lasermarkingsoftware.com
> > > > >
http://www.openapc.com
> > > > >
> > > > > Follow us at Twitter:
https://twitter.com/#!/openapc
> > > > >
> > >
> > >
> > > --
> > > Kind regards
> > >
> > > Jim Hart
> > >
> > >
http://www.lasermarkingsoftware.com
> > >
http://www.openapc.com
> > >
> > > Follow us at Twitter:
https://twitter.com/#!/openapc
> > >
>
>
> --
> Kind regards
>
> Jim Hart
>
>
http://www.lasermarkingsoftware.com
>
http://www.openapc.com
>
> Follow us at Twitter:
https://twitter.com/#!/openapc
>