Unfortunately I rolled it back to the snapshot I made prior to the installation.  I can say I did try the 'ipa-ca-install' command and it broke in pretty much the same way as doing the --setup-ca after uninstalling the server, preparing a new replica from IPA0 and starting IPA1 with a clean sheet.

I will do the 'ipa-ca-install' again, but probably not until Thursday or Friday as I'll be out of the office the next two days to go see my Red Devils play Barcelona.  

If that fails, I'll pull the logs, uninstall the server and start with a freshly prepared replica and install as if it was a new replica with CA and pull those logs if/when that fails. 

On Mon, Jul 24, 2017 at 10:25 PM, Fraser Tweedale <ftweedal@redhat.com> wrote:
On Mon, Jul 24, 2017 at 10:44:24AM -0400, Mark Haney via FreeIPA-users wrote:
> Prior to my employment, one of our engineers setup an IPA server to replace
> the horrific OpenLDAP server. One of my first tasks was to build a second
> IPA server and setup replication.  Initially, the replication setup was
> smooth and simple.  (I used this:
> https://www.howtoforge.com/installing-freeipa-with-replication for getting
> replica up.)
> However, as we were starting to consider how best to deploy it to our remote
> servers, and digging through the GUI I got this pop-up when looking at the
> Topology page:
> It is strongly recommended to keep the CA services installed on more than
> one server.
> As this replica needs to be a full 'replica' of the primary, I went about
> trying to install the CA role on the second server, which I'll call IPA1 and
> the master IPA0.  The RH documentation says to 'Run ipa-replica-install with
> the --setup-ca option.' Of course, the documentation doesn't explicitly say
> whether that needs to be done on the initial creation of the replica, or if
> it can be done after the replica was created.  (IOW, it just adds the CA
> services role and pulls from IPA0 the CA stuff it needs.)
> Unfortunately, that failed and I ended up uninstalling the replica with
> 'ipa-server-install --uninstall' after removing the replica from IPA0.
> After a reboot (just in case), I built a new replica GPG file on IPA0,
> copied it over to IPA1 and ran this:
> ipa-replica-install replica-info-ipa1.neonova.net.gpg --setup-ca
> That also failed with the exact same error as the failure from trying to
> install just the CA role on the existing replica. This is the error I get:
>  [2/27]: configuring certificate server instance
> ipa.ipaserver.install.cainstance.CAInstance: CRITICAL Failed to configure CA
> instance: Command '/usr/sbin/pkispawn -s CA -f /tmp/tmpYC8gIz' returned
> non-zero exit status 1
> ipa.ipaserver.install.cainstance.CAInstance: CRITICAL See the installation
> logs and the following files/directories for more information:
> ipa.ipaserver.install.cainstance.CAInstance: CRITICAL
> /var/log/pki/pki-tomcat
>   [error] RuntimeError: CA configuration failed.
> Your system may be partly configured.
> Run /usr/sbin/ipa-server-install --uninstall to clean up.
> ipa.ipapython.install.cli.install_tool(Replica): ERROR    CA configuration
> failed.
> ipa.ipapython.install.cli.install_tool(Replica): ERROR    The
> ipa-replica-install command failed. See /var/log/ipareplica-install.log for
> more information
> Also, in the pki-tomcat/ca/debug log I get this:
> Failed to contact master using admin
> portjavax.ws.rs.InternalServerErrorException: HTTP 500 Internal Server Error
> issuer: CN=Go Daddy Secure Certificate Authority -
> G2,OU=http://certs.godaddy.com/repository/,O="GoDaddy.com,
> Inc.",L=Scottsdale,ST=Arizona,C=US
> javax.ws.rs.NotFoundException: HTTP 404 Not Found
> We have a signed Wildcard Cert from GoDaddy on IPA0, but I can't tell why
> this even needs to contact the Cert CA for any reason.
> BTW, I had this wildcard cert setup for the IPA web interface only prior to
> blowing this thing to pieces over partial documentation and God knows what
> else isn't spelled out that I missed.
> Any ideas?
Did you create a fresh replica file via `ipa-replica-prepare' after
installing the wildcard cert?  I would do that just in case.

Could you provide more of the /var/log/pki/pki-tomcat/ca/debug log
file (ideally the whole thing)?

Also to clarify: ``ipa-replica-install --setup-ca'' installs a new
replica including the CA role.  To install the CA role on an
existing replica use the ``ipa-ca-install'' command.


Mark Haney
Network Engineer at NeoNova
919-460-3330 (opt 1) • mark.haney@neonova.net