Objective: boot F21 on MK802II Allwinner A10 headless and without serial
console.
Installation instructions used were the "manual" ones from:
Have applied /usr/share/uboot/Mele_A1000/u-boot-sunxi-with-spl.bin using dd
and also tried /usr/share/uboot/Cubieboard/u-boot-sunxi-with-spl.bin
I am presuming that this step would have applied sun4i-a10-a1000.dtb
or have I missed a step?
Have set up wpa on the sdcard before booting using tips from
with edits of
/etc/wpa_supplicant/wpa_supplicant.conf and
/etc/sysconfig/network-scripts/ifcfg-wlan0
As well as the various user folders being empty as listed below the
messages log file shows that the
following Services have failed
abrtd
firewalld
rngd
avahi-daemon
chronyd
sshd-keygen
systemd-logind
dbus
rtkit-daemon
ModemManager
Any tips on where to start looking?
Are there a number of steps to manually do what the firstboot script
normally does by writing to the card before booting?
I need to have sshd start before login if I am to connect wirelessly - I
have no usb ethernet adapter.
Thanks
-------- Forwarded Message --------
Subject: Re: [fedora-arm] Fedora 21 Allwinner A10 Booting?
Date: Mon, 15 Dec 2014 17:58:27 +1100
From: Robert Brown <rebrown(a)exemail.com.au
On Mon, Dec 15, 2014 at 5:24 AM, Robert
Brown<rebrown(a)exemail.com.au> wrote:
> Thanks for the reply Peter.
> On 15/12/14 15:58, Peter Robinson wrote:
>> On Mon, Dec 15, 2014 at 4:52 AM, Robert Brown<rebrown(a)exemail.com.au
>> wrote:
>>> Found several log files with date 01/01/1970 (attached).
>>
>>> /var/log/chrony was
empty.
>> Would be until network comes up and chrony can start
>
>>> Messages log reports:
>>> EXYNOS: PMU not supported and
>>> edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
>>> edma-dma-engine: probe of edma-dma-engine.0 failed with error -22
>> All spurious, for HW other than AllWinner
>
>>> fairly early on. And
>>
>>> ahci-sunxi
1c18000.sata: PHY power up failed.
>>> ahci-sunxi: probe of 1c18000.sata failed with error -5
>> Do you have a SATA device attached?
> No sata device attached.
>
>>> Generated key 1
>>> Fatal error : getpwnam(chrony) failed
>>> getpwnam(chrony) failed
>>
>>> A search found all of
these were empty:
>>
>>>
/media/rbrown/__/etc/systemd/user
>>> /media/rbrown/__/etc/xdg/systemd/user
>>> /media/rbrown/__/var/kerberos/krb5/user
>>> /media/rbrown/__/usr/share/perl5/User
>>> /media/rbrown/__/usr/lib/systemd/user
>>> /media/rbrown/__/run/user
>>
>>> First things to check
for?
>> Maybe I missed in it earlier posts but what A10 device are you using?
> This is a Rikomagic MK802II hdmi device. Trying to boot headless with no
> serial console!
What uboot are you using, are you specifying a .dtb file, if so what one?
Peter
I have applied /usr/share/uboot/Mele_A1000/u-boot-sunxi-with-spl.bin
using dd. This Mele device has shown a very high compatibility
previously with the MK802II. Other u-boot options that I could try might
be Cubieboard (1) and maybe A10-OLinuXino-Lime but less sure of this
last one.
Is my understanding correct that this step would have applied
sun4i-a10-a1000.dtb or have I missed a step?
Rob
_______________________________________________
arm mailing list
arm(a)lists.fedoraproject.org