Hi,
OK, my issue was a "glitch in the matrix". I retried with another sd-card
(Kingston 8GB) and it now just works! My use case is server only, so I will
not test any desktop stuff.
- Fred
On Sat, Apr 4, 2020 at 1:46 AM Thomas H.P. Andersen <phomes(a)gmail.com>
wrote:
On Fri, Apr 3, 2020 at 6:13 PM Stefan Wahren <stefan.wahren(a)i2se.com>
wrote:
> Hi Fred,
>
> Am 03.04.20 um 13:10 schrieb Fred van Zwieten:
> > I haven't retried it yet, but I do have some extra info on my previous
> > (and failed) attempt:
> >
> > I used arm-image-installer as the tool. As it does not yet have a rpi4
> > target, I used the rpi3 value. It does boot, but, like I said, it
> > hangs in a later stage. I will provide screenshots when I am able to
> > test again.
> >
> > This is the (relevant) output from /proc/cpuinfo:
> > Hardware : BCM2835
> > Revision : c03111
> > Serial : 1000000094b1358a
> > Model : Raspberry Pi 4 Model B Rev 1.1
>
> this should work with Linux 5.6. So i don't have an idea what's the
> problem here.
>
I have the exact same model/revision (confirmed with /proc/cpuinfo when
booting raspbian) and mine boots without problems.
These are the steps I did to get it to boot to gnome-shell:
Wrote Fedora-Minimal-32-20200328.n.0.aarch64.raw.xz (latest compose from
koji at the time) with arm-image-installer to the sd.
Resized partion.
Booted and set up users etc.
Once booted I ran:
# dnf update
# dnf install fedora-release-workstation-32 --allowerasing
# dnf group install workstation-product
# dnf install bash-completion
and then after a reboot:
# systemctl start graphical.target
This got me a gnome-shell (on llvmipe obviously, but it is usable)
> Rev 1.2 needs recent changes to sdhci-iproc and the devicetree.
>
> Best regards
> Stefan
>
> >
> > - Fred
> >
> > On Fri, Apr 3, 2020 at 12:25 PM Andreas Reschke <arm_ml(a)rirasoft.de
> > <mailto:arm_ml@rirasoft.de>> wrote:
> >
> > Hello Dirk,
> >
> > I've tried it with balenaEtcher: It works !!
> >
> > Thank you for that tip !!
> >
> > Andreas
> >
> > PS: I dind't know why it not works with xzcat and dd but now I have
> a
> > working method.
> >
> > Am 03.04.20 um 10:23 schrieb Dirk Streubel:
> > >> Hello together,
> > >>
> > >> Hello Dirk
> > >>
> > >> how did you you install
> > Fedora-Minimal-32_Beta-1.2.aarch64.raw.xz on SD-Card?
> > >>
> > >> Just xzcat Fedora-Minimal-32_Beta-1.2.aarch64.raw.xz | dd
> > of=/dev/sdc status=progress bs=4M
> > >>
> > >> didn't work for me. All I get is a dracut shell
> > >>
> > >>
> > >> Thanks
> > >>
> > >> Andreas
> > > Hello Andreas,
> > >
> > > yes, i installed the two Version yesterday on a 64 GB SD Card.
> > >
> > > Image has been unpacked with all necessary tools.
> > >
> > > For installation on the SD Card i use balenaEtcher. That Program
> > works fine here.
> > >
> > > Dirk
> > >
> > >
> > >
> > >
> > >
> > >> _______________________________________________
> > >> arm mailing list -- arm(a)lists.fedoraproject.org
> > <mailto:arm@lists.fedoraproject.org>
> > >> To unsubscribe send an email to
> > arm-leave(a)lists.fedoraproject.org
> > <mailto:arm-leave@lists.fedoraproject.org>
> > >> Fedora Code of Conduct:
> >
https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> > >> List Guidelines:
> >
https://fedoraproject.org/wiki/Mailing_list_guidelines
> > >> List Archives:
> >
>
https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
> > > _______________________________________________
> > > arm mailing list -- arm(a)lists.fedoraproject.org
> > <mailto:arm@lists.fedoraproject.org>
> > > To unsubscribe send an email to
> > arm-leave(a)lists.fedoraproject.org
> > <mailto:arm-leave@lists.fedoraproject.org>
> > > Fedora Code of Conduct:
> >
https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> > > List Guidelines:
> >
https://fedoraproject.org/wiki/Mailing_list_guidelines
> > > List Archives:
> >
>
https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
> > _______________________________________________
> > arm mailing list -- arm(a)lists.fedoraproject.org
> > <mailto:arm@lists.fedoraproject.org>
> > To unsubscribe send an email to arm-leave(a)lists.fedoraproject.org
> > <mailto:arm-leave@lists.fedoraproject.org>
> > Fedora Code of Conduct:
> >
https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> > List Guidelines:
> >
https://fedoraproject.org/wiki/Mailing_list_guidelines
> > List Archives:
> >
>
https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
> >
> >
> > _______________________________________________
> > arm mailing list -- arm(a)lists.fedoraproject.org
> > To unsubscribe send an email to arm-leave(a)lists.fedoraproject.org
> > Fedora Code of Conduct:
>
https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> > List Guidelines:
https://fedoraproject.org/wiki/Mailing_list_guidelines
> > List Archives:
>
https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
> _______________________________________________
> arm mailing list -- arm(a)lists.fedoraproject.org
> To unsubscribe send an email to arm-leave(a)lists.fedoraproject.org
> Fedora Code of Conduct:
>
https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> List Guidelines:
https://fedoraproject.org/wiki/Mailing_list_guidelines
> List Archives:
>
https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
>