Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
I confirmed the xz image has the same hash as is shown on the mirror. I used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout - starts [ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...
[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
Hey,
I experienced not booting SD card when I forgot to unmount the SD before doing the dd command. (especially when another OS was on it) check mounts into /run/media/<username>
Fox
On 05/14/2018 05:26 PM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
I confirmed the xz image has the same hash as is shown on the mirror. I used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
On Tue, May 15, 2018 at 4:42 AM, RENARD Pierre-Francois pfrenard@gmail.com wrote:
Hey,
I experienced not booting SD card when I forgot to unmount the SD before doing the dd command. (especially when another OS was on it) check mounts into /run/media/<username>
Thanks for the suggestion. However this is not my case. I don't have any auto mount settings and I did not mount it before dd. I've tried to dd again several times now but still no lucky.
Fox
On 05/14/2018 05:26 PM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
I confirmed the xz image has the same hash as is shown on the mirror. I used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
arm mailing list -- arm@lists.fedoraproject.org To unsubscribe send an email to arm-leave@lists.fedoraproject.org
Hi,
On 05/14/2018 10:26 AM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
So, two quick questions. What firmware & version are you using, and have you tried booting one of the installer images?
(I tend to use the server iso image, and have had a decent bit of luck with it).
I confirmed the xz image has the same hash as is shown on the mirror. I. used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
On 05/16/2018 01:08 AM, Jeremy Linton wrote:
Hi,
On 05/14/2018 10:26 AM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
So, two quick questions. What firmware & version are you using, and have you tried booting one of the installer images?
(I tend to use the server iso image, and have had a decent bit of luck with it).
Thanks for the suggestions.
I believe I haven't updated firmware after Fedora 27 released. I'll try the installer way later when I have some time.
I confirmed the xz image has the same hash as is shown on the mirror. I. used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...
[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
On 05/17/2018 08:41 PM, Zamir SUN wrote:
On 05/16/2018 01:08 AM, Jeremy Linton wrote:
Hi,
On 05/14/2018 10:26 AM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
So, two quick questions. What firmware & version are you using, and have you tried booting one of the installer images?
(I tend to use the server iso image, and have had a decent bit of luck with it).
Thanks for the suggestions.
I believe I haven't updated firmware after Fedora 27 released. I'll try the installer way later when I have some time.
Hi Jeremy,
I updated to the newest firmware on Linaro website[1]. But boot still stuck in "EFI stub: Exiting boot services and installing virtual address map...". I flashed the firmware from your github[2] and the dracut timeout error is still there. I am posting the console log from the UART here[3].
Addition note that might be useful: 1. The guide of flashing the firmware in[4] do not work for me. After flashing l-loader.bin I cannot flash ptable-*.img(it just hang there without any progress). When I see [5] I tried to flash the recovery.bin first then it works. 2. I cannot type in anything using minicon after system boot to anaconda text installer or dracut emergency shell. So I cannot install the system myself or trying to get more logs. However I can edit the grub menu via console, still not sure why. 3. I did not see anything special with earlycon=pl011,0xf7113000 configured.
[1] https://releases.linaro.org/96boards/hikey/linaro/binaries/latest/ [2] https://github.com/jlinton/OpenPlatformPkg [3] https://paste.fedoraproject.org/paste/cchgFYr~5R6YbjfGm4ZgNg [4] https://github.com/96boards/documentation/wiki/HiKeyUEFI#flash-binaries-to-e... [5] https://www.96boards.org/documentation/consumer/hikey/installation/board-rec...
So can you help with the second point (typing on console)? In that way I can at least debug more myself.
I confirmed the xz image has the same hash as is shown on the mirror. I. used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...
[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
Hi,
Just a quick note here, per IRC this morning in case someone finds this but not that conversation.
On 05/18/2018 12:06 PM, Zamir SUN wrote:
On 05/17/2018 08:41 PM, Zamir SUN wrote:
On 05/16/2018 01:08 AM, Jeremy Linton wrote:
Hi,
On 05/14/2018 10:26 AM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
So, two quick questions. What firmware & version are you using, and have you tried booting one of the installer images?
(I tend to use the server iso image, and have had a decent bit of luck with it).
Thanks for the suggestions.
I believe I haven't updated firmware after Fedora 27 released. I'll try the installer way later when I have some time.
Hi Jeremy,
I updated to the newest firmware on Linaro website[1]. But boot still stuck in "EFI stub: Exiting boot services and installing virtual address map...". I flashed the firmware from your github[2] and the dracut timeout error is still there. I am posting the console log from the UART here[3].
That log looks suspiciously like the hi6220_reset driver being missing from the initrd. Regenerating it with dracut --add-drivers hi6220_reset.ko should may allow SD booting. I tested USB boot this weekend and it works, so the problem seems isolated to SD at the moment.
Addition note that might be useful:
- The guide of flashing the firmware in[4] do not work for me. After
flashing l-loader.bin I cannot flash ptable-*.img(it just hang there without any progress). When I see [5] I tried to flash the recovery.bin first then it works. 2. I cannot type in anything using minicon after system boot to anaconda text installer or dracut emergency shell. So I cannot install the system myself or trying to get more logs. However I can edit the grub menu via console, still not sure why.
This is likely an upstream edk2 bug. I've seen a couple patches for it, and integrated the one from the linaro edk2 repo, but i'm guessing its not working properly. To work around the problem pressing 'esc' during the "...." boot, will exit to the UEFI BDS menus. From there simply booting the device should allow you to interact with grub/etc as normal. Starting the BDS seems to fix whatever is going wrong (although I didn't mention you should double check that your not using XON/XOFF flow control).
- I did not see anything special with earlycon=pl011,0xf7113000 configured.
[1] https://releases.linaro.org/96boards/hikey/linaro/binaries/latest/ [2] https://github.com/jlinton/OpenPlatformPkg [3] https://paste.fedoraproject.org/paste/cchgFYr~5R6YbjfGm4ZgNg [4] https://github.com/96boards/documentation/wiki/HiKeyUEFI#flash-binaries-to-e... [5] https://www.96boards.org/documentation/consumer/hikey/installation/board-rec...
So can you help with the second point (typing on console)? In that way I can at least debug more myself.
I confirmed the xz image has the same hash as is shown on the mirror. I. used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...
[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
On 05/22/2018 03:59 AM, Jeremy Linton wrote:
Hi,
Just a quick note here, per IRC this morning in case someone finds this but not that conversation.
On 05/18/2018 12:06 PM, Zamir SUN wrote:
On 05/17/2018 08:41 PM, Zamir SUN wrote:
On 05/16/2018 01:08 AM, Jeremy Linton wrote:
Hi,
On 05/14/2018 10:26 AM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
So, two quick questions. What firmware & version are you using, and have you tried booting one of the installer images?
(I tend to use the server iso image, and have had a decent bit of luck with it).
Thanks for the suggestions.
I believe I haven't updated firmware after Fedora 27 released. I'll try the installer way later when I have some time.
Hi Jeremy,
I updated to the newest firmware on Linaro website[1]. But boot still stuck in "EFI stub: Exiting boot services and installing virtual address map...". I flashed the firmware from your github[2] and the dracut timeout error is still there. I am posting the console log from the UART here[3].
Hi Jeremy,
That log looks suspiciously like the hi6220_reset driver being missing from the initrd. Regenerating it with dracut --add-drivers hi6220_reset.ko should may allow SD booting. I tested USB boot this weekend and it works, so the problem seems isolated to SD at the moment.
Addition note that might be useful:
- The guide of flashing the firmware in[4] do not work for me. After
flashing l-loader.bin I cannot flash ptable-*.img(it just hang there without any progress). When I see [5] I tried to flash the recovery.bin first then it works. 2. I cannot type in anything using minicon after system boot to anaconda text installer or dracut emergency shell. So I cannot install the system myself or trying to get more logs. However I can edit the grub menu via console, still not sure why.
This is likely an upstream edk2 bug. I've seen a couple patches for it, and integrated the one from the linaro edk2 repo, but i'm guessing its not working properly. To work around the problem pressing 'esc' during the "...." boot, will exit to the UEFI BDS menus. From there simply booting the device should allow you to interact with grub/etc as normal. Starting the BDS seems to fix whatever is going wrong (although I didn't mention you should double check that your not using XON/XOFF flow control).
Thanks for the fruitful info. Actually your firmware works fine. The reason why I cannot type anything, as you mentioned, is because minicom set Hardware Flow Control to YES. Now I can type in after setting it to NO.
And thanks for mentioning you are installing to USB stick. I just tried installing to USB stick and it works(actually I installed to a Samsung mSD card reader with my SD card inserted).
However, after I get it running, I tried to add "hi6220_reset" to dracut config and regenerated the initramfs, then boot from SD (directly from the board), and it still cannot boot. I copied the log out[6] in case it is useful for development.
I also tried to install directly to the SD card, but it failed in creating label on /dev/mmcblk1. I make the installer drop to shell and did not see the mmcblk1 actually.
One more thing that worth mentioning, I tried to use another cheap mSD reader to boot the system after installation, but it seems the cheap mSD simply cannot boot. So I assume there are compatible issue there. The mSD reader that don't work is Bus 002 Device 018: ID 14cd:1212 Super Top microSD card reader (SY-T18)
HTH. Thanks again for your help!
[6] https://paste.fedoraproject.org/paste/CvO988-TC~MD~~8NY1AaCw [7] https://paste.fedoraproject.org/paste/GSkGQLOO4zPN84gMODnhZw
- I did not see anything special with earlycon=pl011,0xf7113000
configured.
[1] https://releases.linaro.org/96boards/hikey/linaro/binaries/latest/ [2] https://github.com/jlinton/OpenPlatformPkg [3] https://paste.fedoraproject.org/paste/cchgFYr~5R6YbjfGm4ZgNg [4] https://github.com/96boards/documentation/wiki/HiKeyUEFI#flash-binaries-to-e...
[5] https://www.96boards.org/documentation/consumer/hikey/installation/board-rec...
So can you help with the second point (typing on console)? In that way I can at least debug more myself.
I confirmed the xz image has the same hash as is shown on the mirror. I. used the following command to write to my TF card. xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 uid=0 au' ] Started Setup [ 222.738436] audit: type=1131 audit(1520288415.819:15): pid=1' Virtual Console.
Starting Dracut Emergency Shell...
[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 auid=4294' Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async page read [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000) [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000H) [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req 1000000)
-
Jeremy Linton -
RENARD Pierre-Francois -
Zamir Sun -
Zamir SUN