Is there some place to watch for that build, or is this list the best place?


On Mon, Mar 24, 2014 at 1:05 PM, Peter Robinson <pbrobinson@gmail.com> wrote:
On Sun, Mar 23, 2014 at 9:46 PM, Jason Porter <lightguard.jp@gmail.com> wrote:
> Hey Peter, hope this is a bit more helpful:

Looks good, the next release of arm-boot-config will add the needed support.

Thanks for the details,

Peter

> U-Boot 2013.10-rc3 (Jan 20 2014 - 13:33:34)
>
> CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
> Reset cause: POR
> Board: UDOO
> DRAM:  1 GiB
> MMC:   FSL_SDHC: 0
> *** Warning - bad CRC, using default environment
>
> auto-detected panel HDMI
> Display: HDMI (1024x768)
> In:    serial
> Out:   serial
> Err:   serial
> Net:   using phy at 6
> FEC [PRIME]
> Hit any key to stop autoboot:  0
> UDOO board => help
> ?       - alias for 'help'
> base    - print or set address offset
> bdinfo  - print Board Info structure
> boot    - boot default, i.e., run 'bootcmd'
> bootd   - boot default, i.e., run 'bootcmd'
> bootm   - boot application image from memory
> bootp   - boot image via network using BOOTP/TFTP protocol
> bootz   - boot Linux zImage image from memory
> clocks  - display clocks
> clrlogo - fill the boot logo area with black
> cmp     - memory compare
> coninfo - print console devices and information
> cp      - memory copy
> crc32   - checksum calculation
> dcache  - enable or disable data cache
> dhcp    - boot image via network using DHCP/TFTP protocol
> echo    - echo args to console
> editenv - edit environment variable
> env     - environment handling commands
> erase   - erase FLASH memory
> exit    - exit script
> ext2load- load binary file from a Ext2 filesystem
> ext2ls  - list files in a directory (default /)
> false   - do nothing, unsuccessfully
> fatinfo - print information about filesystem
> fatload - load binary file from a dos filesystem
> fatls   - list files in a directory (default /)
> fdt     - flattened device tree utility commands
> flinfo  - print FLASH memory information
> go      - start application at address 'addr'
> hdmidet - detect HDMI monitor
> help    - print command description/usage
> icache  - enable or disable instruction cache
> iminfo  - print header information for application image
> imxtract- extract a part of a multi-image
> itest   - return true/false on integer compare
> loadb   - load binary file over serial line (kermit mode)
> loads   - load S-Record file over serial line
> loadx   - load binary file over serial line (xmodem mode)
> loady   - load binary file over serial line (ymodem mode)
> loop    - infinite loop on address range
> md      - memory display
> mdio    - MDIO utility commands
> mii     - MII utility commands
> mm      - memory modify (auto-incrementing address)
> mmc     - MMC sub system
> mmcinfo - display MMC info
> multiboot- manage a multiboot startup
> mw      - memory write (fill)
> nfs     - boot image via network using NFS protocol
> nm      - memory modify (constant address)
> ping    - send ICMP ECHO_REQUEST to network host
> plotmsg - Plot text message on current display (HDMI or LVDS).
>          -r Overwrite last message.
>          -u Start writing just under Logo.
> printenv- print environment variables
> protect - enable or disable FLASH write protection
> reset   - Perform RESET of the CPU
> run     - run commands in an environment variable
> sata    - SATA sub system
> saveenv - save environment variables to persistent storage
> setenv  - set environment variables
> setexpr - set environment variable as the result of eval expression
> showvar - print local hushshell variables
> sleep   - delay execution for some time
> source  - run script from memory
> test    - minimal test like /bin/sh
> tftpboot- boot image via network using TFTP protocol
> true    - do nothing, successfully
> version - print monitor, compiler and linker version
> UDOO board => printenv
> baudrate=115200
> boot_fdt=try
> bootcmd=mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then
> run bootscript; else if run loaduimage; then run mmcbooi
> bootdelay=5
> bootscript=echo Running bootscript from mmc ...; source
> console=ttymxc1
> ethact=FEC
> ethaddr=00:c0:08:88:a2:a2
> ethprime=FEC
> fdt_addr=0x11000000
> fdt_file=imx6q-udoo.dtb
> fdt_high=0xffffffff
> initrd_high=0xffffffff
> ip_dyn=yes
> loadaddr=0x12000000
> loadbootscript=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};
> loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}
> loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}
> mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot}
> ${hdmi_patch} fbmem=24M video=mxcfb0:dev=hdmi,1920x1080M@602
> mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes ||
> test ${boot_fdt} = try; then if run loadfdt; then boo;
> mmcdev=0
> mmcpart=1
> mmcroot=/dev/mmcblk0p1 rootwait rw
> netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs
> ${hdmi_patch} ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp
> netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes;
> then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; $;
> script=boot.scr
> splashpos=m,m
> uimage=/boot/uImage
> update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else
> setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if i
> update_sd_firmware_filename=u-boot.imx
>
> Environment size: 2075/8188 bytes
> UDOO board => iminfo
>
> ## Checking Image at 12000000 ...
> Unknown image format!
> UDOO board => md
> md - memory display
>
> Usage:
> md [.b, .w, .l] address [# of objects]
> UDOO board => mmcinfo
> Device: FSL_SDHC
> Manufacturer ID: 3
> OEM: 5344
> Name: SU16G
> Tran Speed: 50000000
> Rd Block Len: 512
> SD version 3.0
> High Capacity: Yes
> Capacity: 14.8 GiB
> Bus Width: 4-bit
> UDOO board => showvar
> HUSH_VERSION=0.01
> UDOO board =>
>
>
>
> On Sun, Mar 23, 2014 at 7:41 AM, Peter Robinson <pbrobinson@gmail.com>
> wrote:
>>
>> On Sat, Mar 22, 2014 at 2:25 AM, Jason Porter <lightguard.jp@gmail.com>
>> wrote:
>> > Trying to boot the Fedora-Minimal-armhfp-rawhide-20140320-sda image I
>> > downloaded from koji today, looked like the 20140321 builds failed just
>> > gives me a blank screen. Here's the console output from booting their
>> > Ubuntu
>> > image:
>>
>> Not much help. Can you interrupt the boot during the uboot phase (ie
>> before it says "Booting kernel from Legacy Image") and then at the
>> uboot prompt type:
>> help <press enter>
>> printenv <press enter>
>>
>> And the take a copy of all the output for us. The above is using an
>> ancient kernel without DT support and is ancient history ;-)
>>
>> Peter
>
>
>
>
> --
> Jason Porter
> http://en.gravatar.com/lightguardjp



--
Jason Porter
http://en.gravatar.com/lightguardjp