Hi Robert,
----- Original Message -----
I just tested with Fedora-Minimal-armhfp-30-20190307.n.0-sda
On a Cubieboard2:
I installed the image on a 4GB uSD card and deleted all partitions.
I installed the image on a 240GB SSD drive and enlarged the rootfs
partition to about 6GB.
I installed the cards on a Cubieboard2, attached the console and
booted. The boot failed. This process has been working for years, so
something serious has been broken in the uboot.
Thanks for testing and reporting the issue. It seems to affect the allwinner
boards (Cubietruck, Banana Pi etc).
Not fixed in uboot-tools-2019.04-0.4.rc3.fc30. You can use the F29
builds to continue testing until we can get a fix in F30.
Paul
>
> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
> DRAM: 1024 MiB
> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> Trying to boot from MMC1
>
>
> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
>
> CPU: Allwinner A20 (SUN7I)
> Model: Cubietech Cubieboard2
> I2C: ready
> DRAM: 1 GiB
> MMC: mmc@1c0f000: 0
> Loading Environment from FAT... ** No valid partitions found **
> In: serial
> Out: serial
> Err: serial
> SCSI: Target spinup took 0 ms.
> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> flags: ncq stag pm led clo only pmp pio slum part ccc apst
>
> Net: sunxi_set_gate: (CLK#66) unhandled
> eth0: ethernet@1c50000
> starting USB...
> USB0: USB EHCI 1.00
> USB1: USB OHCI 1.0
> USB2: USB EHCI 1.00
> USB3: USB OHCI 1.0
> scanning bus 0 for devices... 1 USB Device(s) found
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning bus 2 for devices... 1 USB Device(s) found
> scanning bus 3 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc0 is current device
> ** Invalid partition 1 **
> scanning bus for devices...
> data abort
> pc : [<7ef86b0e>] lr : [<7ef82d89>]
> reloc pc : [<4a01ab0e>] lr : [<4a016d89>]
> sp : 7af43ad0 ip : 0000001c fp : 000000c0
> r10: 00000000 r9 : 7af4bed8 r8 : 00000000
> r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8
> r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8
> Flags: nZcv IRQs off FIQs off Mode SVC_32
> Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604)
> Resetting CPU ...
>
> resetting ...
>
> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
> DRAM: 1024 MiB
> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> Trying to boot from MMC1
>
>
> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
>
> CPU: Allwinner A20 (SUN7I)
> Model: Cubietech Cubieboard2
> I2C: ready
> DRAM: 1 GiB
> MMC: mmc@1c0f000: 0
> Loading Environment from FAT... ** No valid partitions found **
> In: serial
> Out: serial
> Err: serial
>
> and so forth.
>
> On 3/3/19 5:45 PM, Peter Robinson wrote:
> > On Sun, Mar 3, 2019 at 10:18 PM Robert Moskowitz <rgm(a)htt-consult.com>
> > wrote:
> >> The environment is only the uboot on the uSD and all partitions on the
> >> sata HD.
> >>
> >> I have been doing this for years now with no problem. uboot has always
> >> switched to looking for the sata hd for partitions if no partitions on
> >> the uSD:
> >>
> >> U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000)
> >> DRAM: 1024 MiB
> >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> >> Trying to boot from MMC1
> >>
> >>
> >> U-Boot 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) Allwinner Technology
> >>
> >> CPU: Allwinner A20 (SUN7I)
> >> Model: Cubietech Cubieboard2
> >> I2C: ready
> >> DRAM: 1 GiB
> >> MMC: SUNXI SD/MMC: 0
> >> Loading Environment from FAT... ** No valid partitions found **
> >> In: serial
> >> Out: serial
> >> Err: serial
> >> SCSI: Target spinup took 0 ms.
> >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> >> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> >>
> >> Net: eth0: ethernet@01c50000
> >> starting USB...
> >> USB0: USB EHCI 1.00
> >> USB1: USB OHCI 1.0
> >> USB2: USB EHCI 1.00
> >> USB3: USB OHCI 1.0
> >> scanning bus 0 for devices... 1 USB Device(s) found
> >> scanning bus 2 for devices... 1 USB Device(s) found
> >> scanning usb for storage devices... 0 Storage Device(s) found
> >> Hit any key to stop autoboot: 0
> >> switch to partitions #0, OK
> >> mmc0 is current device
> >> ** Invalid partition 1 **
> >> scanning bus for devices...
> >> Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
> >> Type: Hard Disk
> >> Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
> >> Found 1 device(s).
> >>
> >> Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
> >> Type: Hard Disk
> >> Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
> >> ... is now current device
> >> Scanning scsi 0:2...
> >> Found /extlinux/extlinux.conf
> >> Retrieving file: /extlinux/extlinux.conf
> >> 567 bytes read in 33 ms (16.6 KiB/s)
> >> Ignoring unknown command: ui
> >> Ignoring malformed menu command: autoboot
> >> Ignoring malformed menu command: hidden
> >> Ignoring unknown command: totaltimeout
> >> CentOS-Userland-7-armv7hl-generic-Minimal-1810 Boot Options.
> >> 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810
> >> (4.14.82-201.el7.armv7hl)
> >>
> >> Enter choice: 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810
> >> (4.14.82-
> >> 201.el7.armv7hl)
> >> Retrieving file: /initramfs-4.14.82-201.el7.armv7hl.img
> >>
> >> Yes, this particular event is with the current Centos arm image, but
> >> that should not matter. I have to get this Centos image built and
> >> installed before I can test with Fedora arm image....
> >>
> >> I grabbed a more recent uboot via:
> >>
> >> Fedora-Minimal-armhfp-30-20190301.n.0-sda
> >>
> >> When I try booting with the uboot in that image I get:
> >>
> >> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
> >> DRAM: 1024 MiB
> >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> >> Trying to boot from MMC1
> >>
> >>
> >> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
> >>
> >> CPU: Allwinner A20 (SUN7I)
> >> Model: Cubietech Cubieboard2
> >> I2C: ready
> >> DRAM: 1 GiB
> >> MMC: mmc@1c0f000: 0
> >> Loading Environment from FAT... ** No valid partitions found **
> >> In: serial
> >> Out: serial
> >> Err: serial
> >> SCSI: Target spinup took 0 ms.
> >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> >> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> >>
> >> Net: sunxi_set_gate: (CLK#66) unhandled
> >> eth0: ethernet@1c50000
> >> starting USB...
> >> USB0: USB EHCI 1.00
> >> USB1: USB OHCI 1.0
> >> USB2: USB EHCI 1.00
> >> USB3: USB OHCI 1.0
> >> scanning bus 0 for devices... 1 USB Device(s) found
> >> scanning bus 1 for devices... 1 USB Device(s) found
> >> scanning bus 2 for devices... 1 USB Device(s) found
> >> scanning bus 3 for devices... 1 USB Device(s) found
> >> scanning usb for storage devices... 0 Storage Device(s) found
> >> Hit any key to stop autoboot: 0
> >> switch to partitions #0, OK
> >> mmc0 is current device
> >> ** Invalid partition 1 **
> >> scanning bus for devices...
> >> data abort
> >> pc : [<7ef86b0e>] lr : [<7ef82d89>]
> >> reloc pc : [<4a01ab0e>] lr : [<4a016d89>]
> >> sp : 7af43ad0 ip : 0000001c fp : 000000c0
> >> r10: 00000000 r9 : 7af4bed8 r8 : 00000000
> >> r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8
> >> r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8
> >> Flags: nZcv IRQs off FIQs off Mode SVC_32
> >> Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604)
> >> Resetting CPU ...
> >>
> >> resetting ...
> >>
> >> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
> >> DRAM: 1024 MiB
> >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> >> Trying to boot from MMC1
> >>
> >>
> >> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
> >>
> >> CPU: Allwinner A20 (SUN7I)
> >> Model: Cubietech Cubieboard2
> >> I2C: ready
> >> DRAM: 1 GiB
> >> MMC: mmc@1c0f000: 0
> >> Loading Environment from FAT... ** No valid partitions found **
> >> In: serial
> >> Out: serial
> >> Err: serial
> >>
> >> and so forth....
> >>
> >> If there is a rc3 available, please tell me what image to grab for it
> >> and I can test with that.
> > There should be a rc3 this week.
> >
> _______________________________________________
> arm mailing list -- arm(a)lists.fedoraproject.org
> To unsubscribe send an email to arm-leave(a)lists.fedoraproject.org
> Fedora Code of Conduct:
https://getfedora.org/code-of-conduct.html
> List Guidelines:
https://fedoraproject.org/wiki/Mailing_list_guidelines
> List Archives:
>
https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
>