2018-03-13 8:18 GMT+09:00 Peter Robinson pbrobinson@gmail.com:
On Mon, Mar 12, 2018 at 10:47 PM, sakurai sakurai@pugpug.org wrote:
Hi Peter,
Thank you for your prompt comment. I removed uEnv.txt but following message was displayed.
(snip)
I don't know what you've done to now, you're likely possibly better off starting again with arm-image-installer to setup the image again with am335x_evm and then try booting with the boot button held down.
I tried again using arm-image-installer by following command.
fedora-arm-image-installer --image=Fedora-Server-armhfp-27-1.6-sda.raw.xz --target=am335x_evm --media=/dev/sdd --norootpass --resizefs --addconsole --selinux=off
Not am335x_boneblack? Anyway I installed using arm335x_evm this time.
My boot loader may be new because Angstrom will not boot without holding the boot button.
You might also want to give the full output.
Here is the full output.
U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img
U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)
I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt ** Unable to read file uEnv.txt ** gpio: pin 55 (gpio 55) value is 1 ** File not found /boot/uImage ** U-Boot#
-- SAKURAI, Atsushi sakurai@pugpug.org